Hotpoint CM 9945 H Mode d'emploi Page 25

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 28
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 24
25
Troubleshooting
Below is a list of some possible malfunctions.
If the problem cannot be resolved as described, contact After-sales Service.
PROBLEM POSSIBLE CAUSE REMEDY
The coffee is not hot. - The cups have not been pre-heated.
- The brewing unit has cooled down
because 2/3 minutes have elapsed
since the last coffee was made.
- The set temperature is not high
enough.
- Heat the cups by rinsing them with hot
water.
- Before making coffee, heat the brewing
unit by selecting the RINSE function
from the menu.
- Change the set temperature (see
paragraph Changing the coffee
temperature).
The coffee is not creamy
enough.
- The coffee is ground too coarsely.
-
-
-
- The blend of coffee is unsuitable.
- Turn the grinding adjustment knob one
click anticlockwise towards the number
1 while the coffee mill is in operation
(Figure 14).
- Use a blend of coffee specifically for
espresso coffee machines.
The coffee runs out too slowly
or in drips.
- The coffee is ground too finely. - Turn the grinding adjustment knob one
click clockwise towards the number
7 while the coffee mill is in operation
(Figure 14). Continue one click at a time
until coffee run-off is satisfactory.
- Results are only visible after running off
2 coffees.
The coffee runs out too
quickly.
- The coffee is ground too coarsely. - Turn the grinding adjustment knob one
click anticlockwise towards the number
1 while the coffee mill is in operation
(Figure 14). Avoid turning the grinding
coarseness regulator too far otherwise
when you select 2 cups, the coffee may
run out in drips. Results are only visible
after running off 2 coffees.
The coffee does not run out of
one or either of the spouts.
- The spouts are blocked. - Clean the spouts with a toothpick (Figure
26).
The coffee does not come out
of the spouts, but around the
service door (A2).
- The holes in the spouts are clogged
with dry coffee powder.
- - The coffee feed (A3) inside the
service door is blocked.
- Clean the spouts with a toothpick, a
sponge or a hard bristled kitchen brush
(Figures 26-28).
- Clean the coffee feed (A3) thoroughly,
especially around the hinges.
Water comes out of the spouts
instead of coffee.
- Ground coffee is blocking the funnel
(A21)
- Clean the funnel (A21) with a wooden or
plastic fork and clean the inside of the
machine.
The milk does not come out of
the milk spout (C5).
- The intake tube is not inserted or is
inserted incorrectly.
- Insert the intake tube (C4) in the rubber
washer in the milk container lid (Figure
23).
The milk is not well frothed. - The milk container lid is dirty.
- The milk pointer is incorrectly
positioned.
- Clean the milk container lid as described
in
- paragraph Cleaning the milk container.
- - Adjust the pointer as described in
chapter
- MAKING CAPPUCCINO.
The milk contains large
bubbles or spurts out of
themilk spout
- The milk is not cold enough or is not
semi-skimmed.
- The milk frother pointer is
incorrectly adjusted.
- The milk container lid is dirty.
- Ideally, use skimmed milk at refrigerator
temperature, or semi-skimmed milk at
refrigerator temperature (about 5°C).
If resultsare still not satisfactory, try
changing brand of milk.
- Move the pointer slightly towards the
word CAFFELATTE (see chapter MAKING
CAPPUCCINO).
- Clean the milk container lid as described
in paragraph Cleaning the milk container.
Vue de la page 24
1 2 ... 20 21 22 23 24 25 26 27 28

Commentaires sur ces manuels

Pas de commentaire