Hotpoint VTD00 Manuel d'utilisateur télécharger pdf (Page 5)

Open window venting

The end of the tube

should be directed

downwards, to prevent

warm moist air from

condensing in the room or

in the dryer.

! Ensure that the dryer is adequately ventilated and

that the end of the vent tube is not directed towards

the air intake duct.

! The vent tube must always be fitted for optimum

performance.

! Make sure that the vent tube and air intake vents

are not obstructed or blocked.

! The dryer must not recycle exhaust air.

! Misusing a tumble dryer may create a fire hazard.

! Do not discharge exhaust air into a flue which is

used for exhaust fumes from other appliances that

burn gas or other fuels.

Electrical connections

Make sure of the following before you insert the plug

into the the electrical socket:

●

The socket must be grounded.

●

The socket must be able to sustain the machines

maximum power, which is indicated on the rating

label (see Dryer Description).

●

Power voltage must be within the values indicated

on the rating label (see Dryer Description).

●

The socket must be compatible with the dryers

plug. Should this not be the case, replace the

plug or the socket.

! The dryer must not be installed outdoors, even if the

space is sheltered. It can be very dangerous if it is

exposed to rain or storms.

! Once installed, the dryers electrical wire and plug

must be within easy reach.

! Do not use extension cords.

! The power cord must not be bent or squashed.

! The power cord supplied is fitted with a BS1363 plug

and a 13 amp BS1362 fuse. If you need to replace the

fuse, use only those rated at 13 amp (13A) and ASTA

approved to BS1362.

Moulded plug

! The plug must not be used

without the fuse cover in place.

If a replacement fuse holder/cover

is required, it must be of the

same colour coding or wording

as shown on the base of the plug.

Replacements are available from

authorised dealers.

Changing the plug

The wires in the power cord are coloured in accordance

with the following:

! If the plug being replaced is a non-rewirable type,

then the cut-off plug must be disposed of safely. DO

NOT leave it where it can be inserted into a socket

and create a shock hazard.

! The power supply cord should be checked periodically

and replaced by a cord specially prepared for this

dryer and fitted only by authorised technicians (see

Service). New or longer power cords are supplied at

an extra charge by authorised dealers.

! The manufacturer denies any responsibility should

any of these rules not be followed.

! If in doubt about any of the above consult a qualified

electrician.

Levelling your dryer

The dryer must be installed level for correct operation.

When you have installed

your dryer in its final

location check that it is

level first side to side,

then front to back.

If the dryer is not level,

use a wooden block to

support it while adjusting

the two front legs up or

down, until your dryer is

level.

Before you start using your dryer

Once you have installed your dryer and before you use

it, clean the inside of the drum to remove any dust

that could have accumulated during transport.

Green and Yellow

(Earth) wire to terminal

marked ‘E’, symbol ,

or coloured green and

yellow.

13A ASTA approved

fuse to BS1362.

Brown (Live) wire to

terminal marked ‘L’ or

coloured red.

Blue (Neutral) wire to

terminal marked ‘N’ or

coloured black.

Cord clamp

Installation

Important

Information

Installation

Description

Start and

Programmes Laundry

Warnings and

Suggestions

Maintenance

and Care

Service

Troubleshooting

1 2 3 4 5 6 7 8 9 10 ... 15 16

Commentaires sur ces manuels

Pas de commentaire

Hotpoint VTD00 Manuel d'utilisateur Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Séchoirs Hotpoint VTD00