Hotpoint VTD00 Manuel d'utilisateur télécharger pdf (Page 8)

Start and Programmes

1. Select HIGH HEAT by pressing

the HEAT button.

2. Position the PROGRAMMES knob

on .

3. Press the START button , the

ACTIVE light will turn on.

1. Select HIGH HEAT by pressing

the HEAT button.

2. Position the PROGRAMMES knob

on .

3. Press the START button, the

ACTIVE light will turn on.

Programmes table (VTD20 only)

Programme

What it does...

How to set it...

Note:

Automatic

Drying

(average loads)

Dries completely:

your clothes are ready to be

worn. For average loads (from

1 to 3kg) of Cotton, polycotton

or synthetics.

! If you select LOW HEAT, this

programme will not dry your

clothes. For Acrylic fibres or

small loads select Timed

Drying.

This programme can also be

used for large loads if you

require a slightly drier result.

1. Select HIGH HEAT by pressing

the HEAT button.

2. Position the PROGRAMMES knob

on .

3. Press the START button, the

ACTIVE light will turn on.

Automatic

Drying

(large loads)

Dries completely:

your clothes are ready to be

worn. For large loads (from 3

to 6kg) of Cotton.

! If you select LOW HEAT, this

programme will not dry your

clothes. For Acrylic fibres or

small loads select Timed

Drying.

This programme can also be

used for average loads if you

prefer a damper result.

Timed Drying

up to 120 minutes

Dries wet clothes that will be

ironed, Acrylic fibres, or small

loads (less than 1kg).

Consult suggested drying

times (see Laundry).

Always allow the dryer to

complete this phase.

This is the programmes final phase.

Approximately 10 minutes before

the finish, the knob advances

automatically to the Cool Tumble

Phase. After this, the Buzzer will

sound (if selected) and the clothing

is ready to be taken out.

Heating elements turn

themselves off and clothing

is cooled down.

1. Select required heat setting HIGH

HEAT or LOW HEAT by pressing

the HEAT button.

2. Position the PROGRAMMES knob

on the desired time.

3. Press the START button, the

ACTIVE light will turn on.

Easy Iron

Cool Tumble

Phase

Brief programme

(approximately 10 minutes)

that softens fibres of clothing

that is ready for ironing.

This is not a drying

programme (see below).

Easy Iron Programme

‘Easy Iron’ is a short 10 minute programme (8 minutes of heat followed by a 2 minute cool tumble period) which

fluffs the fibres of clothing that have been left in the same position/location for an extended period of time. The

cycle relaxes the fibres and makes them easier to iron and fold.

! ‘Easy Iron’ is not a drying programme and should not be used for wet articles of clothing.

For best results:

1. Do not load more than the maximum capacity.

These numbers refer to the dry weight:

Fabric Maximum load

Cotton and Cotton mixtures 2.5kg

Synthetics 2kg

Denim 2kg

2. Unload the dryer immediately after the end of the programme, hang, fold or iron the articles and put

them away in the closet. Should this not be possible repeat the programme.

The ‘Easy Iron’ effect varies from one fabric to the next. It works well on traditional fabrics like Cotton or Cotton

mix, and less well on acrylic fibres and on materials such as Tencel®.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Commentaires sur ces manuels

Pas de commentaire

Hotpoint VTD00 Manuel d'utilisateur Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Séchoirs Hotpoint VTD00