Hotpoint AQC9 2F7 TM2 1 (EU) Mode d'emploi télécharger pdf (Page 17)

One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the following troublesho-

oting suggestions.

Possible causes / Solutions:

• The plug is not plugged into the socket, or not making contact.

• There has been a power failure.

• The fuse has blown. Try to plug another appliance into the socket.

• You are using an extension cord. Try to plug the dryer’s power cord directly into the

socket.

• The door is not closed securely.

• The programme has not been set properly (see Start and Programmes).

• The START button has not been pressed (see Start and Programmes).

• You have set a delay time (see Start and Programmes).

• You have pressed the start button; there will be a short delay before the dryer starts.

Wait for drying to begin,do not press the start button again or the dryer will pause

and not begin drying.

• The filter has not been cleaned (see Maintenance).

• The water container needs emptying? The empty water

light is flashing and “h2o”

message is displayed?

(see Maintenance).

• The Heat Pump Filter needs cleaning (see Maintenance).

• The temperature setting is not ideal for the type of fabric you are drying (see Start and

Programmes, and Laundry).

• The correct drying time has not been selected for this load (see Laundry).

• The air intake grille is obstructed (see Installation and see Maintenance).

• The items are too wet (see Laundry).

• The dryer is overloaded (see Laundry).

• The water container was probably not emptied at the start of the programme. Do

not wait for the empty water signal always check and empty the container before

starting a new drying programme (see Maintenance).

• This is normal the empty water flashes when the container is full. If the light is on but not

flashing its just a reminder to empty the container (see Start and Programmes).

! For safety the dryer has a maximum programme time of 5 hours. If an automatic

programme has not sensed the required final moisture in this time the dryer will

complete the programme and stop. Check the above points and run the programme

again, if the results are still to damp, contact the service centre (see Service).

• If the display shows F followed by one or two numbers, Turn off and remove plug,

Clean the Filters (see Maintenance). Then replace plug turn on and start another

program.

If the number is displayed again Note down the number and contact the service

centre (see Service).

• The dryer is in ‘Demo’ mode. Press and hold both the On/Off and Start/Pause

buttons for 3 seconds. The display will show “dOn” for 3 seconds and then the

dryer will resume normal operation.

• The time to end is continuously monitored throughout the drying cycle and the time

is adjusted to give the best-estimated time. The displayed time may increase during

the cycle and this is normal.

• This is normal, particularly if the dryer has not been used for a while. If the noise

persists throughout the whole drying cycle then contact the service centre.

• The dryer has gone into standby mode to save power. This occurs if you have left the

dryer on or have had a power cut. It occurs after 30 minutes:

- if you leave the dryer without starting a programme;

- after your drying programme has finished.

Press and hold the ON/OFF button until the dryer reactivates

Problem:

The dryer won’t start.

Drying cycle will not begin.

It is taking a long time to dry.

The Empty water light is flashing but

the dryer has only been running for a

short period.

Empty water light is on and the water

container is not full.

Programme finishes and clothes dam-

per than expected.

The Display shows a fault code F follo-

wed by one or two numbers, the option

lights and pause light are flashing.

The display briefly shows “dOn”

every 6 seconds.

Time to End display changes during

drying.

The dryer makes a thumping noise du-

ring the first few minutes of operation.

The lights on the dryer control panel

are off although the dryer is switched

on.

Troubleshooting

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 55 56

Commentaires sur ces manuels

Pas de commentaire

Hotpoint AQC9 2F7 TM2 1 (EU) Mode d'emploi Page 17

Commentaires sur ces manuels

Produits connexes et manuels pour Sèche-linge électrique Hotpoint AQC9 2F7 TM2 1 (EU)