Hotpoint AQC9 6F7 TM1 (EU) Mode d'emploi télécharger pdf (Page 34)

Maintenance and Care

Switching off the electricity

! Unplug the dryer when not using it, when cleaning it, and

during maintenance activities.

Clean the filter after each cycle

The filter is an important part of your dryer: it accumulates

lint and fluff that is formed while drying.

When finished drying, clean the filter by rinsing it under

running water or with your vacuum cleaner. Should the

filter become clogged up, the airflow inside the dryer will be

seriously compromised: drying times lengthen and you will

consume more energy. It may also damage your dryer.

The filter is found in front of the dryer trim (see diagram).

Removing the filter:

1. Pull the plastic grip of the

filter upwards (see diagram).

2. Open the filter by

depressing the clip.

3. Clean the lint from the

inside of the filter, and

replace it correctly. Ensure

the filter is fully located flush

into the tumble dryer trim.

! Do not use dryer without replacing the filter.

Check the drum after each cycle

Turn the drum manually in order to remove small items

(handkerchiefs) that could have been left behind.

Cleaning the drum

! Do not use abrasives, steel wool or stainless steel

cleaning agents to clean the drum.

A coloured film may start to appear on the stainless steel

drum, this may be caused by a combination of water

and, or cleaning agents such as fabric conditioner from

the wash. This coloured film will not affect the dryer

performance.

Empty the Water Container after each cycle

Pull the container out of the dryer and empty it into a sink or

other suitable drain. Replace container securely.

Always check and empty the container before you start a new

drying programme.

Cleaning the Heat Pump Filter Unit

• Periodically (every 5 drying cycles) remove Heat pump

filter unit and clean any build up of fluff from the

surface of the filter by rinsing it under running water or with

your vacuum cleaner.

We however recommend that you clean this filter after

every drying cycle to optimize the dryers performance.

To remove Heat pump filter unit:

1. Unplug the dryer and open the door.

2. Remove the filter unit by rotating the 4 clips to the vertical

position then pulling the filter unit towards you.

3. Separate the two parts of the filter unit

and clean the surface of the filter.

! Warning: The front of the heat pump

is made from thin metal plates.

Take care that you do not damage these

or cut yourself when cleaning, removing

or replacing the filter unit.

4. If there is any build up of fluff on the

plates Carefully clean this off with a

damp cloth,sponge or vacuum cleaner. Never use your Fingers.

5. Assemble the two parts of the filter clean the surface of the

seals and replace with the 4 clips into the horizontal position,

sure that the catches have been secured.

Cleaning the dryer

• External parts in metal or plastic and rubber parts can

be cleaned with a damp cloth.

• Periodically (every 6 months) vacuum the front Air intake

grille, to remove any build up of fluff, lint or dust. Also to

remove accumulation of fluff from the front of Heat Pump filter

unit and filter areas, clean occasionally with a vacuum cleaner.

! Do not use solvents or abrasives.

! Your dryer uses special bearing components which do not

need lubrication.

! Have your dryer checked regularly by authorized technicians

to ensure electrical and mechanical safety (see Service).

Water Contaniner

Catches

Filter

Handle

Air Intake

Heat Pump

Filter Unit

Heat Pump Filter

Unit Cover

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 55 56

Commentaires sur ces manuels

Pas de commentaire

Hotpoint AQC9 6F7 TM1 (EU) Mode d'emploi Page 34

Commentaires sur ces manuels

Produits connexes et manuels pour Sèche-linge électrique Hotpoint AQC9 6F7 TM1 (EU)