Hotpoint CX109SV6 (CR) AUS Mode d'emploi télécharger pdf (Page 27)

AUS

Installation

LEVELLING

Your cooker is heavy, so it would be advisable for

two people to move it. The cooker is fitted with rear

wheels and will slide into position easily. Movement

of your cooker is most easily achieved as follows.

Open the grill/oven door sufficiently to allow a

comfortable grip on the underside front edge of the

oven roof, avoiding any grill or oven interior furniture,

and then lift and slide back at the same time.

Your cooker must stand on a flat surface so that the

hob is perfectly level, and the cooker is stable and

cannot be rocked, this is easily achieved by

adjusting the three feet which are under the front of

the cooker and the 3 castors under the rear of the

cooker, if necessary.

Installing the shelves

When inserting the shelves onto the guide rails,

ensure the raised section is towards the rear of the

oven. This prevents food from falling off the back of

the tray.

Safety Chain

In order to prevent

accidental tipping of

the appliance, for

example by a child

climbing onto the open

oven door, the supplied

safety chain must be

installed.

Ensure the chain is

secured to the rear wall

of the oven, and attach

the chain to a hook or screw secured to the wall

behind the appliance.

NOTE: If the cooker is to be placed on a base,

precautions must be taken to prevent it from

slipping off the base.

The cooker is designed to match the depth of

standard 600mm worktops.

An adaptor backplate should, therefore, be fitted

within the shaded area shown to allow the cooker to

be pushed fully to the wall. If a forward facing

backplate is used, it must be chased into the wall.

This appliance is suitable for use with either a

flexible connection or rigid copper connection.

Check The Gas Type

WARNING: Before installation, check that the gas

type (natural gas or LPG/Propane) of the cooker is

suitable for the gas type available to the installation.

It is extremely dangerous to use the wrong gas type

with any appliance, as fire or serious injury can

result.

This cooker is supplied from the factory already set

for Natural Gas. To convert the cooker to LPG (or

back to Natural Gas from LPG), follow the directions

later in this section.

Fit regulator supplied for Natural Gas (if applicable)

at rear of appliance, and as close as practicable to

the appliance.

It is recommended that an isolating valve and union

be fitted, to enable simple disconnection for

servicing. These are to be in an accessible location.

Gas Connection

Either a rigid metal pipe with fittings in compliance

with the standards in force must be used for

connecting to the nipple union (threaded ½"G male

fitting) situated at the rear of the appliance to the

right (fig.8), or an approved flexible hose of class B

or D.

Should it be necessary to turn the fitting, the gasket

(supplied with the appliance) must be replaced.

If a flexible hose is used, it should be as short as

possible with a maximum length of 1.5 metres;

" The flexible connection must be approved to

class B or D of AS/NZS1869 as a minimum.

" it should not be bent, kinked or compressed;

" it should not be in contact with the rear wall of the

appliance or in any case with parts which may

reach a temperature of 50°C;

" it should not come into contact with pointed parts

or sharp corners;

" it should not be subject to any pulling or twisting

forces;

" it should be easy to inspect along its entire length

in order to be able to check its condition.

" The supply connection point must be accessible

1 2 ... 22 23 24 25 26 27 28 29 30 31 32

Commentaires sur ces manuels

Pas de commentaire

Hotpoint CX109SV6 (CR) AUS Mode d'emploi Page 27

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires de cuisine et de ménage Hotpoint CX109SV6 (CR) AUS