Hotpoint FF4DAX Instructions d'exploitation télécharger pdf (Page 2)

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR 5 YEAR PARTS GUARANTEE ON 08448 24 24 24

Installation

Connection of the water supply

To carry this out, use the kit provided which contains all

the necessary elements for connection to the water

supply.

To improve the performance of the Aqua Care, we

recommend that you fit a tap with a filter on the pipe for

the connection to the water system: in this way it will be

possible to manually interrupt the water supply during

long periods in which Aqua Care is not used.

! The water pressure inside the water system must be

between 0.8 bar and 8 bar.

! The appliance must only be connected to a water

supply suitable for drinking.

Your appliance is supplied with a 13amp fused plug that

can be plugged into a 13amp socket for immediate use.

Before using the appliance please read the instructions

below.

WARNING:

THIS APPLIANCE MUST BE EARTHED.

Replacing fuse covers:

When replacing a faulty fuse, a 13amp ASTA approved

fuse to BS 1362 should always be used and the fuse

cover re-fitted.

If the fuse cover is lost, the plug must not be used until

a replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the

correct colour as indicated by the coloured marking or the

colour that is embossed in words on the base of the plug.

Changing the plug:

Removing the plug

If your appliance has a non-rewireable moulded plug

and you should wish to remove it to add a longer cable

or to re-route the mains cable through partitions, units

etc. please ensure that either:

- The plug is replaced by a fused 13amp re-

wireable plug bearing the BSI mark of

approval.

- The mains cable is wired directly into a

13amp cable outlet, controlled by a

switch (in compliance with BS 5733)

which is accessible without moving the

appliance.

! Before placing your new appliance into operation

please read these operating instructions carefully. They

contain important information for safe use, for installation

and for care of the appliance.

! Please keep these operating instructions for future

reference. Pass them on to possible new owners of the

appliance.

Positioning and connection

Positioning

1. Place the appliance in a well-ventilated humidity-free room.

2. Do not obstruct the rear fan grills. The compressor and

condenser give off heat and require good ventilation to

operate correctly and save energy.

3. Leave a space of at least 10 cm between the top part of

the appliance and any furniture above it, and at least 12

cm between the sides and any furniture/side walls.

4. Ensure the appliance is away from any sources of heat

(direct sunlight, electric stove, etc.).

5. In order to maintain the correct distance between the

appliance and the wall behind it, fit the spacers supplied

in the installation kit, following the instructions provided.

Levelling

1. Install the appliance on a level and rigid floor.

2. If the floor is not perfectly horizontal, adjust the

refrigerator by tightening or loosening the front feet.

Electrical connections

After the appliance has been transported, carefully

place it vertically and wait at least 3 hours before

connecting it to the electricity mains. Before inserting

the plug into the electrical socket ensure the following:

• The appliance is earthed and the plug is compliant with

the law.

• The socket can withstand the maximum power of the

appliance, which is indicated on the data plate located

on the bottom left side of the fridge (e.g. 150 W).

• The voltage must be in the range between the values

indicated on the data plate located on the bottom left

side (e.g. 220-240V).

• The socket is compatible with the plug of the appliance.

If the socket is incompatible with the plug, ask an

authorised technician to replace it (

see Assistance

). Do

not use extension cords or multiple sockets.

! Once the appliance has been installed, the power supply

cable and the electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by

authorised technicians only (see Assistance).

! The manufacturer declines any liability should these

safety measures not be observed.

1 2 3 4 5 6 7 ... 11 12

Commentaires sur ces manuels

Pas de commentaire

Hotpoint FF4DAX Instructions d'exploitation Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Réfrigérateurs-congélateurs côte à côte Hotpoint FF4DAX