Hotpoint KELON HISENSE - KELO Mode d'emploi télécharger pdf (Page 31)

100

- 31 -

Remote controller

Function description of buttons (P1-04)

1. ON/OFF BUTTON

Starts or Stops the appliance by

pressing this button.

3.FAN BUTTON

Used to select fan speed in sequence

auto, high, medium or low.

4-5.TEMPERATURE BUTTON

Used to select the room

temperature.

Used to set the time in timer mode.

6. SMART BUTTON

Sets or cancels Smart operation.

7. SWING BUTTON

Stops or starts horizontal adjustment

louver swinging and sets the desired

up/down airow direction.

10-11. HUMIDITY BUTTON

Used to set desired humidity level,

they are only available under 6th

SENSE mode.

16. SUPER SILENT BUTTON

Used to start or stop the super

silent operation to have a low noise

environment.

2. MODE BUTTON

Used to select the operation mode.

In sequence Cooling, hearing or fan.

8.SLEEP BUTTON

Used to select the sleep mode in

sequence of sleep 1, sleep 2, sleep 3

sleep 4 and sleep o.

9.AROUND U BUTTON

Used to set or cancel Around U

function.

12.JET BUTTON

Used to start or stop the fast cooling

or heating.

13.DIM BUTTON

Used to turn on or turn o display

light on indoor unit.

14.WI-FI BUTTON

Used to trun on or turn o the Wi-Fi.

15TIMER BUTTON

Used to set the time for turn on or

turn o the appliance.

Symbols on RC display Active RC by pressing UNLOCK button

Cooling indicator Auto fan speed Sleep indicator 1

Press the button, the

backlight will lighted up

and function buttons

will be activated for use.

Press again to lock remote

controller. If no operation

on remote controller

for 10s, the remote

controller will be locked

automatically.

PRESS

Humidity plus indicator High fan speed Sleep indicator 2

Humidity minus indicator Medium fan speed Sleep indicator 3

Fan only indicator Low fan speed Sleep indicator 4

Heating indicator Super silent indicator Display set temperature

Around U indicator Smart Indicator

OF F

Display set timer

Jet indicator Power save indicator Signal transmission

PROTECTION

Operating condition

The protective device maybe trip

and stop the appliance in the cases

listed below.

Heating Outdoor air

temperature is

over 24°C

Outdoor air

temperature is

below -7°C

Room temperature

is over 27°C

Cooling Outdoor air

temperature is

over 43°C

Room temperature

is below 21°C

Dehumidifying Room temperature

is below 18°C

If the air conditioner runs in

COOLING or DRY mode with door

or window opened for a long time

when relative humidity is above

80%, dew may drip down from the

outlet.

Features of protection device

Wait at least 3 minutes before

restarting the unit after operation

stops or changing mode during

operation. After connecting to

power supply and turning on the

appliance immediately, a delay of 20

seconds may occur before it starts to

operate. If all operation has stopped,

press ON/OFF button again to

restart. Timer should be set again if it

has been cancelled.

Features of COOLING mode

Anti-freezing When the temperature

of the indoor heat exchanger drops

to 0° or below, compressor will stop

working to protect the appliance.

Features of HEATING mode

Preheating

In order to prevent cool air blowing,

2-5 minutes are necessary to

preheat the indoor unit at HEATING

operation start. The indoor fan will

not work during preheating.

Defrosting

In HEATING operation the appliance

will defrost (de-ice) automatically

to raise eciency. This procedure

usually lasts 6-10 minutes. During

defrosting, fan stops running and

running indicator ashes.

After defrosting is completeed,

it returns to HEATING mode

automatically.

1 2 ... 26 27 28 29 30 31 32 33 34 35 36 ... 99 100

Commentaires sur ces manuels

Pas de commentaire

Hotpoint KELON HISENSE - KELO Mode d'emploi Page 31

Commentaires sur ces manuels