Hotpoint FETV 60C P (UK) Mode d'emploi

Naviguer en ligne ou télécharger Mode d'emploi pour Séchoirs à tambour Hotpoint FETV 60C P (UK). Hotpoint FETV 60C P (UK) Instruction for Use Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 4
  • Table des matières
  • DEPANNAGE
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
Step 1
Open the door of your dryer
Step 2
Pull out the fi lter (using the
two fi nger grips)
Step 3
Clean the fl uff off the fi lter
and replace it correctly.
Ensure that the fi lter is
pushed fully home.
Step 4
Make sure the fi lter is pushed fully home
NEVER run the dryer without the fi lter in position
Failure to clean the fi lter after EVERY drying
cycle will affect the drying performance of your
machine. It will take longer to dry and as a result
will use more electricity during drying.
At least every two or three months you MUST
clean fl uff build up around the fi lter housing and
the vent tube.
INSTALLATION
WHERE TO PUT YOUR DRYER
1
0
m
m
15 mm
15 mm
15 mm
15 mm
If you are going to install the
appliance under a work
counter be sure to leave a
10mm space between the top
and any other objects on or
above the machine and a
15mm space between the
sides and any kitchen units or
walls to ensure proper air circulation. The dryer
must never be installed behind a lockable door, a
sliding door or a door with a hinge on the
opposite side to that of the dryer door.
The appliance must be installed with the rear
surface placed against a wall.
VENTILATION
When the dryer is in use there has to be adequate ventilation
to avoid the back fl ow of gases into the room from appliances
burning other fuels, including open fi res.
The vent tube should not exceed 2.4 metres in length.
The tube should be kept clear of the air intake vent and kinks or
‘U’ bends must be avoided as these will obstruct the tube and trap
condensation.
VENTING
Wall mounting
Keep the tube as short and as straight
as possible to prevent condensation
forming in the vent pipe.
The duct in the wall should slope
slightly downwards.
Window mounting
The hole in the window should be as
low down as possible and the tube should be kept as short as
possible.Depending on how often you use your tumble dryer, it is
essential that areas A and B are checked periodically to remove
lint or debris.
This symbol reminds you to read this booklet.
B
A
Open window venting
The end of the tube should be
directed downwards, to prevent
warm moist air from condensing in
the room or dryer.
Do not discharge exhaust air into
a fl ue which is used for exhaust
fumes from other appliances that
burn gas or other fuels.
Do not discharge exhaust air into an extraction system or any duct
with an extractor fan. This will affect the way the thermal controls
operate and can result in a fi re hazard.
ELECTRICAL CONNECTIONS
The socket must be grounded. The power supply
cord should be checked periodically. If the
supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly
qualifi ed persons in order to avoid a hazar
LEVELLING YOUR DRYER
The dryer must be installed level for
correct operation. When you have
installed your dryer in its fi nal location
check that it is fi rst level side to side and
then back to front.
If the dryer is not level use a wooden
block to support it while adjusting the
two front legs up or down until your
dryer is level.
BEFORE YOU START USING YOUR DRYER
Once you have installed your dryer and before you
use it clean the inside of the drum to remove any
dust that could have accumulated during transport.
Air intake vent
Do not block or obstruct
Caution: Hot!
Vent Tube fi tted here
Instruction booklet
TUMBLE DRYER
FETV 60C
TVFM 60C
TVYM 60C
Vue de la page 0
1 2 3 4

Résumé du contenu

Page 1 - Instruction booklet

Step 1Open the door of your dryerStep 2Pull out the fi lter (using the two fi nger grips)Step 3Clean the fl uff off the fi lter and replace it correctly.

Page 2 - Warnings

Check the vent tube and any permanent venting fi xture to make sure that there has been no accumulation of fl uff or lint. Remove lint that collects aro

Page 3 - Troubleshooting

Dryer DescriptionThe TIMER knob sets the drying time: rotate it clockwise, NEVER COUNTER-CLOCKWISE, until the indictor is pointing to the drying time

Page 4 - 11/2016 Xerox Fabriano

DISPOSAL OF OLD ELECTRICAL APPLIANCESThe European Directive 2012/19/EC on Waste Electrical and Electronic Equipment (WEEE) requires that old household

Commentaires sur ces manuels

Pas de commentaire