Hotpoint TVM 570 P (UK) Mode d'emploi télécharger pdf

Step 1

Open the door of your dryer

Step 2

Pull out the lter (using the two

nger grips)

Step 3

Clean the u o the lter and

replace it correctly.

Ensure that the lter is pushed

fully home.

Step 4

Make sure the lter is pushed fully home

NEVER run the dryer without the lter in position

Failure to clean the lter after EVERY drying cycle will

aect the drying performance of your machine. It

will take longer to dry and as a result will use more

electricity during drying.

At least every two or three months you MUST clean

u build up around the lter housing and the vent

tube.

INSTALLATION

WHERE TO PUT YOUR DRYER

15 mm

If you are going to install the

appliance under a work counter

be sure to leave a 10mm space

between the top and any other

objects on or above the machine

and a 15mm space between the

sides and any kitchen units or

walls to ensure proper air

circulation. The dryer must never be installed behind a

lockable door, a sliding door or a door with a hinge on

the opposite side to that of the dryer door.

The appliance must be installed with the rear surface

placed against a wall.

VENTILATION

When the dryer is in use there has to be adequate ventilation to avoid

the back ow of gases into the room from appliances burning other

fuels, including open res.

The vent tube should not exceed 2.4 metres in length.

The tube should be kept clear of the air intake vent and kinks or ‘U’ bends

must be avoided as these will obstruct the tube and trap condensation.

VENTING

Wall mounting

Keep the tube as short and as straight as possible to prevent

condensation forming in the vent pipe.

The duct in the wall should slope slightly

downwards.

Window mounting

The hole in the window should be as low

down as possible and the tube should be

kept as short as possible.Depending on

how often you use your tumble dryer, it is essential that areas A and B

are checked periodically to remove lint or debris.

Open window venting

The end of the tube should be directed downwards, to prevent warm

This symbol reminds you to read this booklet.

moist air from condensing in the room

or dryer.

Do not discharge exhaust air into a

ue which is used for exhaust fumes

from other appliances that burn gas

or other fuels.

Do not discharge exhaust air into an

extraction system or any duct with an

extractor fan. This will aect the way the

thermal controls operate and can result

in a re hazard.

ELECTRICAL CONNECTIONS

The socket must be grounded. The power supply cord

should be checked periodically. If the supply cord is

damaged, it must be replaced by the manufacturer, its

service agent or similarly qualied persons in order to

avoid a hazard

LEVELLING YOUR DRYER

The dryer must be installed level for correct

operation. When you have installed your

dryer in its nal location check that it is rst

level side to side and then back to front.

If the dryer is not level use a wooden block

to support it while adjusting the two front

legs up or down until your dryer is level.

BEFORE YOU START USING YOUR DRYER

Once you have installed your dryer and before you use

it clean the inside of the drum to remove any dust that

could have accumulated during transport.

Air intake vent

Do not block or obstruct

Caution: Hot!

Vent Tube tted here

Instruction booklet

TUMBLE DRYER

TVM 570 P

TVFM 70B GP

Our ideas. Your home.

1 2 3 4

Résumé du contenu

Page 1 - Instruction booklet

Step 1Open the door of your dryerStep 2Pull out the lter (using the two nger grips)Step 3Clean the u o the lter and replace it correctly. Ensure

Page 2 - Warnings

Check the vent tube and any permanent venting xture to make sure that there has been no accumulation of u or lint. Remove lint that collects around

Page 3 - Troubleshooting

Dryer DescriptionThe HEAT button selects drying temperature. OUT: LOW heat IN: HIGH heat. The TIMER knob:: the 0 position swithes o the dryer.The TI

Page 4 - TVFM 70B GP

1951604150010/2018Repairs and After SalesFor product help and advice, repairs, spare parts oraccessories, we’re here to help.For local repair engineer