Hotpoint HS MC 07A ZO UK Mode d'emploi télécharger pdf (Page 9)

Using the motorized brush

When the product is not in the upright position, the power

suction and the rotating brush are working. To pause the

vacuum cleaner use the start/stop button (32) When the

product is in the park position, the Start&Pause function

switches off the operation of the rotating brush, while the

suction power is on. In this position it is possible to use

the other accessories in the clamp (17).

In cases of using of vacuum cleaner by the handle (E)

This allows you to clean surfaces not accessible with

the motorized brush.

1. Place the suction selector on the accessory

position (27) in the back main body.

2. Fit the two-in-one accessory (24) into the handle

frame, pushing down the handle slide clamp (18).

3. To remove the handle, press the handle release

button (31) and pull it out.

4. Press start/stop button (32) and to start the appliance

press the electronic power regulator (33).

FEATURES

Electronic power regulator

When press this button (33) on the main body the

suction power works cyclically (med -> max -> min

-> med). It allows to set the suction power required.

Ultraviolet light

The UV light (if available) (4) is an ultraviolet steriliza-

tion function, when the brush is collecting dust on the

ground normally, the UV lamp is lighting, antiseptic

function is working. When the brush is not in contact

with an horizontal surface, the UV light is switched off.

To replace the UV light, please contact the nearest

Authorised Service Centre.

Hepa lter

This model comprises the Hepa lter. The Hepa lter

ensures maximum protection against allergens and high

air quality, because the air given back by the appliance

is entirely free from dust/ powder residues.

CLEANING AND MAINTENANCE

Before cleaning or maintaining the vacuum cleaner, make

sure it has been unplugged from the electrical outlet. Do

not use aggressive substances or abrasive materials to

clean the appliance, its internal parts and attachments.

Use a dry or slightly damp soft cloth for cleaning. Make

sure the appliance and all its parts are thoroughly dry

before restarting the appliance. We suggest to clean the

lter at least every 6 months to restore its ltering power.

In any case we recommend replacing the lter at least

every year to ensure maximum performance. Always

operate the vacuum cleaner with the lter installed.

Cleaning the dustbin

For the routine cleaning of the dustbin (G):

1. Press the dustbin release button (6) and take out

the dustbin assembly (7).

2. Keep the dustbin assembly in vertical position

with the lid facing down.

3. Press the lock on the dustbin lid (16) to open the

dustbin container (15).

4. Empty the dustbin.

5. Close the dustbin lid until it clicks into place and

replace it into the main body.

For the washing of dustbin container to remove any

residual dirt (G,H):

1. Before washing the dustbin container, make sure

it has been emptied.

2. Align the screw on the back of the motor cover

(11) with the unblock mark on the dustbin (15) to

open the dustbin, turn the upper dustbin same as

the picture (G).

3. Take out the multicyclonic lter (13).

4. Take out the lower multicyclone (14) from dustbin

container, holding the metal handle same as the

picture (H2).

5. Remove any residual dirt by washing the dustbin

container under running water.

6. Let it dry at room temperature until its parts are

thoroughly dry.

7. Assembly in the reverse order the lower multicy-

clone and the lter.

8. Align the screw on the back of the motor cover

(11) with the blocked mark on the dustbin to

close the dustbin, turn the upper dustbin same

as the picture (G).

9. When the screw on the back of the motor cover

(11) and the blocked mark on the dustbin are lined

up completely, the dustbin is correctly tted.

10. Replace the dustbin assembly into the main

body.

Cleaning the lters (H)

To clean the Hepa lter (10):

1. Open the lter cover (9) using the lever of the

handle on the dustbin same as the picture (H3).

2. Remove the Hepa lter turning it in the direction

indicated on the lter (H4).

3. Wash the lter under running water, taking care

that the jet of water is not too strong.

4. Hold it so that the water ows parallel to its folds.

5. Let it dry at room temperature until all of its parts

are thoroughly dry.

6. Replace the Hepa lter and assembly in the

reverse order.

1 2 3 4 5 6 7 8 9 10 11 12 13 14

Commentaires sur ces manuels

Pas de commentaire

Hotpoint HS MC 07A ZO UK Mode d'emploi Page 9

Commentaires sur ces manuels