Hotpoint ITWD 61252 G (PL) Mode d'emploi télécharger pdf (Page 13)

EN 11

If your washing machine has no display, check which of the previously described situations could be

the origin of the fault and follow the corresponding instructions.

F-12/2014

Failure indicator

lights up

Indication on display

(if available)

Description - Causes - Solutions

“Service”

“bdd”

(in case your washing

machine has no display:

all lamps of the

programme ﬂow bar light

up)

Appliance stops during the programme. “Drum ﬂaps

open” (the drum ﬂaps have not been closed properly).

Push the “Reset” button for at least 3 seconds and wait

until the “Door open” lights up. Open lid and close

drum ﬂaps, then select and start desired programme

again. If fault persists, notify our After-Sales Service.

from “F02” to “F35”

(except “F09”)

“Electrical module fault”.

Select and start “Drain” programme or push “Reset”

button for at least 3 seconds.

“F09”

“Water level too high” (after programme cancellation or

false operating). Switch off appliance and then switch it

on again, select programme “Drain” and start within 15

sec.

“FA”

“Waterstop fault”

Switch off appliance, pull out mains plug and turn water

tap off. Tilt appliance forward carefully to allow collected

water to ﬂow out from the bottom. Then:

• Plug in the appliance again.

• Turn the water tap on (if water immediately ﬂows into

the appliance without the appliance being started,

there is a failure; turn off the tap and notify After-Sales

Service).

• Select and start the desired programme again.

“Fod”

“Overfoaming”

Too much foam interrupted the wash programme.

• Select and start “Rinse & Spin” programme.

• Afterwards select and start desired programme again,

using less detergent.

If faults persist, unplug the appliance, turn off the water

tap and contact our After-Sales Service

“Water tap

closed” −

Appliance has no or insufﬁcient water supply. The “Start

(Pause)” light blinks. Check whether:

• Water tap is fully open and water supply pressure is

sufﬁcient.

• Kinks are present in water inlet hose.

• Mesh ﬁlter of water supply hose is blocked (see “Care

and Maintenance”).

• Water hose is frozen up.

• Safety valve inspection window of your water supply

hose is red (provided your appliance has a water

supply hose as shown on picture 21 - see previous

chapter “Care and Maintenance”); replace the hose by

a new one available through our After-Sales Service or

your specialist dealer.

After problem has been removed, restart programme

by pressing “Start (Pause)”. If the fault occurs again,

contact our After-Sales Service.

“Clean pump”

−

Waste water is not pumped out. The appliance stops in

the corresponding programme step; unplug it and check

whether:

• Kinks are present in the drain hose.

• Filter or pump is blocked (see chapter “Cleaning the

Filter/ Draining Residual Water”; make sure the water

has cooled before draining the appliance).

• The drain hose is frozen up.

After problem has been removed, select and start “Drain”

programme or push “Reset” button for at least 3 seconds;

afterwards restart desired programme. If the fault occurs

again, contact our After-Sales-Service.

Description of failure indicators

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 35 36

Commentaires sur ces manuels

Pas de commentaire

Hotpoint ITWD 61252 G (PL) Mode d'emploi Page 13

Commentaires sur ces manuels

Produits connexes et manuels pour Machines à laver Hotpoint ITWD 61252 G (PL)