Hotpoint ITWD 61252 G (PL) Mode d'emploi télécharger pdf (Page 5)

EN 3

DESCRIPTION OF THE WASHING MACHINE (picture 1)

a. Lid

b. Detergent dispenser

c. Drum

d. Pump access behind ﬁlter

e. After-Sales Service sticker (behind the ﬁlter cover)

f. Mobility lever (depending on model). To move the

washing machine: pull the handle out a little bit by

hand and pull it out to the stop with the foot.

g. Adjustable feet

INSTALLATION

Removal of transport bracket

The washing machine is ﬁtted with a transport bracket

to avoid any possible damage during transport.

IMPORTANT: Before using the washing machine,

the transport bracket at the back MUST be

removed.

1. Unscrew the two screws “A” and the four screws

“B” with a ﬂat screwdriver or a No. 8 hex nut box

spanner (picture 2).

2. Remove the transport bracket (picture 3).

3. Replace the four outer screws “B” on the machine

and tighten them (picture 2).

4. Clip the two covers “C” supplied into the openings

“D” of the washing machine (picture 4).

Note: do not forget to replace and tighten the four

outer screws.

Adjust the feet (picture 5, 6)

Install the washing machine on a level surface, near

to electrical, water and drain connections.

If the ﬂoor is uneven, adjust the feet (do not insert

pieces of wood, cardboard etc. under the feet):

1. Screw out the washing machine´s feet by hand

with 2-3 clockwise turns and then slacken the

locknut by wrench.

2. Adjust the height of the feet by hand.

3. Retighten the locknut by turning it anti-clockwise

towards the washing machine’s bottom.

Make sure that the feet are resting correctly on the

ﬂoor and that the washing machine is perfectly

level and stable (use a spirit level).

The washing machine can be installed in an area 40

cm wide and 63 cm deep.

Note: if you install the machine on thick carpet, adjust

the feet to ensure that there is sufﬁcient space under

the machine for the air to circulate.

Connect the water inlet hose (picture 7)

1. Carefully screw the water inlet hose to the valve

on the rear side of the washing machine (A); screw

the other end of the hose to the tap by hand.

2. Make sure there are no kinks in the hose.

3. Check water-tightness of tap and washing machine

connections by turning the tap completely on.

• If the hose is too short, replace it with a suitable

length of pressure resistant hose (1000 kPa min,

EN 61770 approved type).

• If you need a longer waterstop hose, contact our

After Sales Service or your dealer.

• Check the inlet hose regularly for brittleness and

cracks and replace if necessary.

• The washing machine can be connected without a

backﬂow valve.

Water stop anti-ﬂooding system (picture 8)

(if available)

• Screw the hose to the water supply tap. Turn the

tap fully on and check the water-tightness of the

connection.

• The washing machine must not be connected to

the mixing tap of a non-pressurized water heater!

• Do not immerse the water stop device of the hose

into water; otherwise it will loose its protective

function.

• If the ﬂexible hose is damaged, unplug the washing

machine from the mains immediately, turn off the

tap and replace the hose.

• If the ﬂexible hose is too short, replace it with a 3

m Water Stop hose (available from After-Sales

Service or from your dealer).

Connect the water drain hose (picture 9)

Unhook the drain hose from the left clip, see arrow

“A” on picture.

Important:

Do NOT loosen the drain hose from the right con-

nection, see arrow “B” on picture. Otherwise, there

is the risk of leakage and of scalding with hot water.

Firmly connect the drain hose to the siphon or another

outlet for drain water.

If you need to add an extension, use a ﬂexible hose

of the same size and secure the unions with screw-on

hose clips.

Maximum overall drain hose length: 2.50 m.

Maximum drain height: 100 cm.

Minimum drain height: 55 cm.

Important:

Make sure there are no kinks in the drain hose and

take precautions against it falling while the washing

machine is running.

1 2 3 4 5 6 7 8 9 10 ... 35 36

Commentaires sur ces manuels

Pas de commentaire

Hotpoint ITWD 61252 G (PL) Mode d'emploi Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Machines à laver Hotpoint ITWD 61252 G (PL)