Hotpoint DFG 03 TK Mode d'emploi télécharger pdf (Page 14)

Installation

Keep this instruction manual in a safe place for future

reference. If the appliance is sold, given away or moved, please

ensure the manual is kept with the machine, so that the new

owner may benefit from the advice contained within it.

Please read this instruction manual carefully: it contains

important information regarding the safe installation, use and

maintenance of the appliance.

If the appliance must be moved at any time, keep it in an

upright position; if absolutely necessary, it may be tilted onto its

back.

This appliance is intended to be used in household and

similar applications such as:

- staff kitchen areas in shops, offices and other working

environments;

- farm houses;

- by clients in hotels, motels and other residential type

environments;

- bed and breakfast type environments.

Positioning and levelling

1. Remove the appliance from all packaging and check that it

has not been damaged during transportation.

If it has been damaged, contact the retailer and do not proceed

any further with the installation process.

2. Check the dishwasher by placing it so that its sides or back

panel are in contact with the adjacent cabinets or even with the

wall. This appliance can also be recessed under a single

worktop

* (

see the Assembly instruction sheet

3. Position the dishwasher on a level and sturdy floor. If the floor

is uneven, the front feet of the appliance may be adjusted until it

reaches a horizontal position. If the appliance is levelled correctly,

it will be more stable and much less likely to move or cause

vibrations and noise while it is operating.

*. Adjust the height of the rear foot from the front of the appliance

on the central lower part of the dishwasher, turning a hexagonal

spanner (red color) with an opening of 8 mm in a clockwise

direction to increase the height or in an anticlockwise direction to

decrease the height.

Connecting the water and electricity

supplies

Connection to the water and electricity supplies should only

be performed by a qualified technician.

The dishwasher should not stand on top of the water hoses

or the electricity supply cable.

The appliance must be connected to the water supply

network using new hoses.

Do not use old hoses.

The water inlet and outlet hoses and the electricity supply cable

may be positioned towards the right or the left in order to achieve

the best possible installation.

Connecting the water inlet hose

• To a suitable cold water connection point: before attaching

the hose, run the water until it is perfectly clear so that any

impurities that may be present in the water do not clog the

appliance; after performing this operation, screw the inlet hose

tightly onto a tap with a ¾ gas threaded connection.

• To a suitable hot water connection point: your dishwasher

may be supplied with hot water from the mains supply (if you

have a central heating system with radiators) provided that it

does not exceed a temperature of 60°C.

Screw the hose to the tap as described for connection to a

cold water supply.

If the inlet hose is not long enough, contact a specialist store

or an authorised technician (

see Assistance

The water pressure must be within the values indicated in the

Technical data table (

see adjacent information

The hose should not be bent or compressed.

Connecting the water outlet hose

Connect the outlet hose (without bending it) to a drain

duct with a minimum diameter of 4 cm.

The outlet hose must be at a height ranging from 40 to 80

cm from the floor / surface where the dishwasher rests (A).

Before connecting the water outlet hose to the sink drain,

remove the plastic plug (B).

Anti-flooding protection

To ensure floods do not occur, the dishwasher:

- is provided with a special system which blocks the water supply

in the event of anomalies or leaks from inside the appliance.

Some models are also equipped with the supplementary safety

device

New Acqua Stop

*, which guarantees anti-flooding

protection even in the event of a supply hose rupture.

WARNING: HAZARDOUS VOLTAGE!

Under no circumstance should the water inlet hose be cut as it

contains live electrical parts.

* Only available in selected models.

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 23 24

Commentaires sur ces manuels

Pas de commentaire

Hotpoint DFG 03 TK Mode d'emploi Page 14

Commentaires sur ces manuels

Produits connexes et manuels pour Lave-vaisselle Hotpoint DFG 03 TK