Hotpoint FDDSN 11010 P Mode d'emploi télécharger pdf (Page 16)

Troubleshooting

Whenevertheappliancefailstoworkproperly,checkforasolutionfromthefollowinglistbeforecallingforAssistance.

*Onlyavailableinselectedmodels.

Problem: Possible causes / Solutions:

The dishwasher does not start or cannot be

controlled.

• Switch off the appliance by pressing the ON/OFF button, switch it back

on after approximately one minute and reset the cycle.

• The appliance has not been plugged in properly.

• The dishwasher door has not been shut properly.

The door won’t close.

• The lock was released. Strongly push the door until a “clacking” noise is

heard.

No water drains from the

dishwasher.

• The dishwasher cycle has not yet finished.

• The water drain hose is bent (see Installation.)

• The drain duct is blocked.

• The filter is clogged up with food residues.

The dishwasher makes excessive

noise.

• The dishes are rattling against each other or against the sprayer arms.

• An excessive amount of foam has been produced: the detergent has not

been measured out correctly or it is not suitable for use in dishwashers

(see Start-up and use.)

The dishes and glasses are covered

in a white film or limescale deposits.

• The level of refined salt is low or the dosage setting is not suitable for

the hardness of the water (see Rinse aid and salt.)

• The lid on the salt dispenser is not closed properly.

• The rinse aid has been used up or the dosage is too low.

The dishes and glasses are streaked

or have a bluish tinge.

• The rinse aid dosage is too high.

The crockery has not been dried

properly.

• A wash cycle without a drying cycle has been selected.

• The rinse aid has been used up or the dosage is too low (see Rinse aid

and salt.)

• The rinse aid setting is not suitable.

• The crockery is made from non-stick material or plastic.

The crockery is not clean. • The racks are overloaded (see Loading the racks.)

• The crockery has not been arranged well.

• The sprayer arms cannot rotate freely.

• The wash cycle is too gentle (see Wash cycles.)

• An excessive amount of foam has been produced: the detergent has not

been measured out correctly or it is not suitable for use in dishwashers

(see Start-up and use.)

• The lid on the rinse aid compartment has not been shut correctly.

• The filter is dirty or blocked (see Care and maintenance.)

• The refined salt level is low (see Rinse aid and salt.)

The dishwasher does not take any

water in - Tap shut-off alarm (short

beeps are heard)

(the ON/OFF indicator light flashes,

the “Tap shut-off” symbol is lit

and the display shows the text:

No water. Turn tap on. After a few

seconds F 06 appears.)

• There is no water in the mains supply.

• The water inlet hose is bent (see Installation.)

• Turn on the tap and the appliance will start after a few minutes.

• The appliance lock has been activated because no action was taken

when the beeps sounded.

Switch off the machine using the ON/OFF button, turn on the tap and

switch the machine back on after a few seconds by pressing the same

button. Re-program the appliance and restart the wash cycle.

Water inlet hose alarm / Water inlet

filter blocked

(the ON/OFF indicator light ashes, the

“Filter” symbol is lit and the display shows

the textF 07.)

• Switch off the appliance by pressing the ON/OFF button. Shut off the

water tap to eliminate the risk of flooding and remove the plug from the

electrical socket.

Make sure the water inlet filter has not become blocked by impurities

(see “Care and maintenance” chapter.)

1 2 ... 11 12 13 14 15 16 17 18 19 20

Commentaires sur ces manuels

Pas de commentaire

Hotpoint FDDSN 11010 P Mode d'emploi Page 16

Commentaires sur ces manuels

Produits connexes et manuels pour Lave-vaisselle Hotpoint FDDSN 11010 P