Hotpoint FDEF 33121 G Mode d'emploi télécharger pdf (Page 14)

Rinse aid and refined salt

Only use products which have been specifically designed

for dishwashers.

Do not use table salt or industrial salt, or washing up liquid.

Follow the instructions given on the packaging.

If using a multi-functional product it is not necessary to any

add rinse aid; however, we recommend that you add salt,

especially if you live in an area where the water is hard or

very hard.

(Follow the instructions given on the packaging).

If you do not add salt or rinse aid, the LOW SALT* and

LOW RINSE AID indicator lights will remain lit.

Measuring out the rinse aid

Rinseaidmakesiteasierforthecrockerytodry,aswaterruns

off surfaces more readily and therefore does not leave streaks

or marks. The rinse aid dispenser should be filled:

•WhentheLOWRINSEAID* indicator light on the control panel

is illuminated, a reserve supply of rinse aid is still available

for1-2cycles;

1.Openthedispenser“D” by pressing and pulling up the tab

on the lid;

2. Carefully introduce the rinse aid as far as the maximum

reference notch of the filling space - avoid spilling it. If this

happens, clean the spill immediately with a dry cloth.

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the tub.

Rinse-aid dispenser setting

If you are not completely satisfied with the drying results, you

may adjust the quantity of rinse aid.

SwitchonthedishwasherusingtheON/OFFbutton,waitafew

secondsandthenswitchitoffusingtheON/OFFbutton.Press

theStart/Pausebutton3times.

SwitchonthedishwasherusingtheON/OFFbutton,youenter

the menu for setting and rinse aid indicator light shown on the

display

(set to factory level).

AdjustthelevelofrinseaidsupplyusingtheECOcyclebutton.

(from0to4max)

Press the ON/OFF button to save the setting.

IftherinseaidlevelissettoZERO,norinseaidwillbesupplied.

TheLOWRINSEAIDindicatorlightwillnotilluminateifyourun

out of rinse aid.

• Iftherearestreaksonthecrockery,settheadjustmentdevice

toalowernumber(1-2).

• If there are drops of water or limescale marks, set the

adjustment device to a higher number (3-4).

Setting the water hardness

Every dishwasher is equipped with a water softener which, by

using refined salt designed especially for this type of appliance,

supplies water without limescale which is then used to wash

the crockery.

This dishwasher offers a setting which helps to reduce pollution

and optimises washing performance in accordance with the

Water Hardness Table

Average salt container

capacity duration**

Level °dH °fH mmol/l months

1 0 - 6 0 - 10 0 - 1 7 months

2 6 - 11 11 - 20 1,1 - 2 5 months

3 12 - 17 21 - 30 2,1 - 3 3 months

4 17 - 34 31 - 60 3,1 - 6 2 months

34 - 50 61 - 90 6,1 - 9 2/3 weeks

For values between 0°f and 10°f, we do not recommend the

use of salt. * this setting may cause a slight increase in the

duration of the cycles. ** for 1 wash cycle per day.

water hardness level in your area. This information can be

obtained from your local water supplier.

Switch on the dishwasher using the ON/OFF button, wait a few

secondsandthenswitchitoffagain(ON/OFFbutton).Holddown

theStart/Pausebuttonfor3seconds,switchonthedishwasher

usingtheON/OFFbutton,you enter the menu for setting and

the Salt indicator light shown on the display

(water softener set

to medium level).

Adjust the hardness level using the ECO wash-cycle button;

(from1tomax.5* levels.)

Press the ON/OFF button to save the setting.

Even if using multi-functional tablets, the salt dispenser should

still be filled.

(°dH=hardnessmeasuredinGermandegrees-°f=hardness

measuredinFrenchdegrees–mmol/l=millimolesperlitre)

Measuring out the refined salt

In order to obtain the best possible results from a wash cycle,

make sure that the salt dispenser is never empty.

Refinedsaltremoveslimescalefromthewater,thusavoiding

the formation of deposits on crockery.

The salt dispenser is located in the lower part of the dishwasher

(seeDescription)

and should be filled:

• Whenthegreenfloat* cannot be seen by simply looking at

the cap of the salt dispenser;

•WhentheLOWRINSEAIDindicatorlightonthecontrolpanel

is illuminated *;

1.Removethelowerrackandunscrewthe

cap (anticlockwise).

2.Thefirsttimeyoudothis:fillthewater

tank right up to its edge.

3. Position the funnel*

(see figure)

and

fill the salt dispenser up to the edge

(approximately1kg).Itisnormalforalittle

water to leak out.

4.Removethefunnel*andwipeanysaltresiduesawayfrom

the opening; rinse the cap under running water and then screw

it on, the head facing downwards so as to let the water flow out

of the four slots (star-shaped) on the lower part of the cap (cap

with green float*).

It is advisable to perform this procedure every time you add

salt to the dispenser.

Make sure the cap is screwed on tightly so that no detergent can

get into the container during the wash cycle (this could damage

the water softener beyond repair).

Whennecessary,measureoutthesaltbeforeawashcycle

so that any saline solution which has leaked out of the salt

dispenser is removed.

*Onlyavailableinselectedmodels.

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 20

Commentaires sur ces manuels

Pas de commentaire

Hotpoint FDEF 33121 G Mode d'emploi Page 14

Commentaires sur ces manuels

Produits connexes et manuels pour Lave-vaisselle Hotpoint FDEF 33121 G