Hotpoint LTF 11M121 O UK Mode d'emploi télécharger pdf (Page 13)

Rinse aid and refined salt

Only use products which have been specifically designed

for dishwashers.

Do not use table salt or industrial salt, or washing up liquid.

Follow the instructions given on the packaging.

If using a multi-functional product it is not necessary to any

add rinse aid; however, we recommend that you add salt,

especially if you live in an area where the water is hard or

very hard.

(Follow the instructions given on the packaging).

If you do not add salt or rinse aid, the LOW SALT* and

LOW RINSE AID indicator lights will remain lit.

Measuring out the rinse aid

Rinseaidmakesiteasierforthecrockerytodry,aswaterruns

off surfaces more readily and therefore does not leave streaks

or marks. The rinse aid dispenser should be filled:

•WhentheLOWRINSEAID* indicator light on the control panel

is illuminated, a reserve supply of rinse aid is still available

for1-2cycles;

1.Openthedispenser“D” by pressing and pulling up the tab

on the lid;

2. Carefully introduce the rinse aid as far as the maximum

reference notch of the filling space - avoid spilling it. If this

happens, clean the spill immediately with a dry cloth.

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the tub.

Adjusting the amount of rinse aid

If you are not completely satisfied with the drying results, you

may adjust the quantity of rinse aid used. Switch on and off the

dishwasherusingtheON/OFFbutton.PressthePbuttonthree

times.PresstheON/OFFbutton,thesetlevelappearsonthe

display

(defaultsettingofrinseaidislevel2).

Adjust the rinse aid supply level with the P button.

Press the ON/OFF button to save the adjustment setting.

TherinseaidlevelcanbesettoZERO,insuchacasetherinse

aid will not be supplied and the low rinse aid indicator light in

case of running out.

A maximum of 4 levels can be set according to the dishwasher

model.

•Iftherearestreaksonthecrockery,settoalownumber(1-2).

•In case ofdropsofwaterorlimescalemarks,settoahigh

number number (3-4).

Setting the water hardness

Every dishwasher is equipped with a water softener which, by

using refined salt designed especially for this type of appliance,

supplies water without limescale which is then used to wash

the crockery.

This dishwasher offers a setting which helps to reduce pollution

and optimises washing performance in accordance with the

water hardness level in your area. This information can be

obtained from your local water supplier.

Water Hardness Table

Average salt container

capacity duration**

Level °dH °fH mmol/l months

1 0 - 6 0 - 10 0 - 1 7 months

2 6 - 11 11 - 20 1,1 - 2 5 months

3 12 - 17 21 - 30 2,1 - 3 3 months

4 17 - 34 31 - 60 3,1 - 6 2 months

34 - 50 61 - 90 6,1 - 9 2/3 weeks

For values between 0°f and 10°f, we do not recommend the

use of salt

. * this setting may cause a slight increase in the

duration of the cycles. ** for 1 wash cycle per day.

Switch on and off the dishwasher using the ON/OFF button.

Press and hold the P button for a few seconds until you hear

abeep.SwitchonthedishwasherwiththeON/OFFbutton,the

set level appears on the display

(the water softening system is

set by default to level 3).

Adjust the water hardness level with the P button,

(1-2-3-4-5*

see water hardness table)

up to a max. of 5 levels.

Press the ON/OFF button to save the adjustment setting.

Even if using multi-functional tablets, the salt dispenser should

still be filled.

(°dH=hardnessmeasuredinGermandegrees-°f=hardness

measuredinFrenchdegrees–mmol/l=millimolesperlitre)

Measuring out the refined salt

In order to obtain the best possible results from a wash cycle,

make sure that the salt dispenser is never empty.

Refinedsaltremoveslimescalefromthewater,thusavoiding

the formation of deposits on crockery.

The salt dispenser is located in the lower part of the dishwasher

(seeDescription)

and should be filled:

• Whenthegreenfloat* cannot be seen by simply looking at

the cap of the salt dispenser;

•WhentheLOWRINSEAIDindicatorlightonthecontrolpanel

is illuminated *;

1. Remove the lower rack and

unscrew the cap (anticlockwise).

2.Thefirsttimeyoudothis:fillthe

water tank right up to its edge.

3. Position the funnel

(see figure)

and fill the salt dispenser up to the

edge (approximately 1 kg). It is

normal for a little water to leak out.

4.Removethefunnel*andwipeany

salt residues away from the opening; rinse the cap under running

water and then screw it on, the head facing downwards so as to

let the water flow out of the four slots (star-shaped) on the lower

part of the cap (cap with green float

*).

It is advisable to perform this procedure every time you add

salt to the dispenser.

Make sure the cap is screwed on tightly so that no detergent can

get into the container during the wash cycle (this could damage

the water softener beyond repair).

Whennecessary,measureoutthesaltbeforeawashcycle

so that any saline solution which has leaked out of the salt

dispenser is removed.

*Onlyavailableinselectedmodels.

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 19 20

Commentaires sur ces manuels

Pas de commentaire

Hotpoint LTF 11M121 O UK Mode d'emploi Page 13

Commentaires sur ces manuels

Produits connexes et manuels pour Lave-vaisselle Hotpoint LTF 11M121 O UK