Hotpoint AKT 100/WH Mode d'emploi télécharger pdf (Page 2)

INSTALLATION

Recommendations

Important: Disconnect the hob from the mains before carrying

out any installation work or servicing.

• All electrical connections must be made before connecting the

appliance to the power supply.

• Installation must be carried out by a qualified technician in

accordance with the manufacturer's instructions and in

compliance with local regulations.

• Unpack the hob and make sure that the appliance has not been

damaged during transport. If you are not sure contact the

dealer or the nearest service centre.

Preparing the housing unit

• Cut the worktop to fit before installing the appliance. Carefully

remove any shavings or sawdust that could prevent the

appliance from running properly.

Attention: to install the cooktop on other surfaces than wood

(plastic, ceramic, marble, stone, etc.) remember to ask After Sales

Service for the fixing plates (fig. 6).

• The hob must be fitted in a worktop with a minimum thickness

of 20 mm and a maximum of 50 mm.

• There must be nothing between the hob and the oven

(e.g. cables, insulating material, etc.).

• An adjacent column unit must be installed at least 100 mm

from the edge of the hob.

• Cut an opening in the worktop of the given dimensions.

• We recommend you seal the internal edges of the worktop

with wood glue or silicone.

• If not already in place, apply the supplied seal to the hob,

after cleaning the adhesive surface thoroughly.

Glass-ceramic hob

Important: remove any protective film before installing the

hob.

Make sure that that the opening in the worktop for the hob is cut

according to the dimensions given in the drawing, paying attention to

the tolerance range.

The hob should not be forced into the worktop. Forcing the glass-

ceramic top may cause it to crack (even at a later date)!

• If the worktop is made of wood, use the appropriate

brackets, spring clips and screws provided.

• Position the 4 clips (A), if not alreay fitted, around the cooktop

frame, in the slots provided, see Fig. 1.

• Measure the centre of the vertical sides of the cut out a shown

in Fig. 2.

• Position the centre of the brackets (C) on the centre of the

side previously identified.

• The upper edge of the brackets must be flush with the

worktop surface.

• Secure using the 4 screws (B) provided that should screwed

into the pre-prepared holes.

• Insert the cook hob into the pre-prepared hole ensuring that

the clips (A) lodge into the bracket slots provided

(C Fig. 4 and 5).

Electrical connection

• Regulations require that the appliance be earthed.

• Connection to the mains must be carried out by a qualified

technician in accordance with the manufacturer's instructions

and in compliance with local regulations.

• The installer is responsible for connecting appliances correctly

to the mains and for observing the safety regulations.

• After the oven has been installed, the electrical components

must be inaccessible.

• Important: do not connect the oven to the power supply

before you have finished connecting the oven and cooktop.

• Before connecting the oven (or box) to the power supply,

make sure that the hob is among the ones listed in the hob/

oven pairing product sheet provided.

• Connect the connectors of the hob (G) to the connectors of

the oven (F) matching the colours and alignment of the housing

guides visible on the top of the connectors.

• Then make the connection by pushing the connectors all the

way in, making sure that the tongue clicks into place.

• Unscrew the nut of the ground screw (H) (fig. 8)

on the top covering of the oven and insert the yellow/green

ground cable, leaving the washer in place. Screw the nut back

onto the screw and tighten it as far as it will go.

Important: if the connection and colour coding of the hob terminals

do not comply with the data given on the hob/oven pairing product

sheet located on the top of the oven, please request the adapter kit

code AMC 873, available from After Sales Service.

Declaration of conformity

• This hob is suitable for contact with foodstuffs and complies

with EEC (CE) Regulation n. 1935/2004.

• This hob (Class Y) has been designed to be used only for

cooking. Any other use (such as heating a room) is improper

and dangerous.

• This hob has been designed, constructed and marketed in

compliance with:

- safety objectives of the “Low Voltage” Directive 2006/95/CE

(which replaces 73/23/CEE and subsequent amendments);

- protection requirements of EC Directive “EMC” 2004/108;

- requirements of EEC Directive 93/68.

The Manufacturer reserves the right to change product specifications

without prior notice.

Fig. 1

Fig. 3

Fig. 2

Fig. 4

Fig. 5

Fig. 6

Fig. 7

Fig. 8

1 2

HOB INSTRUCTIONS 1
INSTALLATION 2

Commentaires sur ces manuels

Pas de commentaire

Hotpoint AKT 100/WH Mode d'emploi Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Plaques chauffantes Hotpoint AKT 100/WH