Hotpoint RA720KCT Manuel d'installation télécharger pdf (Page 4)

LEVEL THE RANGE

WARNING: Never completely remove the leveling leg

as the range will not be secured to the anti-tip device properly.

MODELS WITH STORAGE DRAWER OR KICK PANELS

Plug in unit and slide into place. Pull drawer out until it stops.

Lift front of drawer until the stops clear the guide. Remove the drawer.

Install the oven shelves in the oven and position the range where

it will be installed.

Check for levelness by placing a spirit level on one of the oven shelves.

7DNHWZRUHDGLQJV³ZLWKWKHOHYHOSODFHGGLDJRQDOO\ILUVW

in one direction and then the other.

The front leveling legs can be adjusted from the bottom

and the rear legs can be adjusted from the top or the bottom.

Use an adjustable wrench to adjust the leveling legs until

the range is level.

REPLACE THE WIRE COVER

Replace wire cover on range back by sliding its left edge under the retaining tabs and replace the

screws removed earlier. Make sure that no wires are pinched between cover and range back.

Wire cover

5 screws to

remove wire

cover

Retaining

tabs

Back of range

Terminal

block cover

Screw to

remove

terminal

block cover

Back of range

ANTI-TIP DEVICE INSTALLATION

To reduce the risk of tipping the range, the

range must be secured by a properly installed

anti-tip bracket. See installation instructions

shipped with the bracket for complete details

before attempting to install.

To check if the bracket is installed and

engaged properly, look underneath the range

to see that the rear leveling leg is engaged

in the bracket. On some models, the storage

drawer or kick panel can be removed for

easier inspection. If visual inspection is not

possible, slide the range forward, confirm the anti-tip bracket is securely attached to the floor or wall, and

slide the range back so the leveling leg is under the anti-tip bracket. If the range is pulled from the wall for

any reason, always repeat this procedure to verify the range is properly secured by the anti-tip bracket.

Never completely remove the leveling legs or the range will not be secured to the anti-tip bracket.

• A child or adult can tip the range and be killed.

• Install the anti-tip bracket to the wall or floor.

• Engage the range to the anti-tip bracket by sliding the

range back such that the foot is engaged.

• Re-engage the anti-tip bracket if the range is moved.

• Failure to do so can result in death or serious burns

to children or adults.

Tip-Over Hazard

WARNING

Stop

FINAL INSTALLATION CHECKLIST

• Check to make sure the circuit breaker is closed (RESET) or the circuit fuses are replaced.

• Be sure power is in service to the building.

• Check that all packing materials and tape have been removed. This will include tape on metal panel under

control knobs (if applicable), adhesive tape, wire ties, cardboard and protective plastic. Failure to remove

these materials could result in damage to the appliance once the appliance has been turned on and

surfaces have heated.

• Check that the door and drawer are parallel to each other and that both operate smoothly. If they

do not, see the Owner’s Manual for proper replacement.

• Check to make sure that the rear leveling leg is fully inserted into the Anti-Tip bracket and that the bracket

is securely installed.

OPERATION CHECKLIST

• Turn on one of the surface units to observe that the element glows within 60 seconds. Turn the unit

off when glow is detected. If the glow is not detected within the time limit, recheck the range wiring

connections. If change is required, retest again. If no change is required, have building wiring checked for

proper connections and voltage.

• Check that the Clock (on models so equipped) display is energized. If a series of horizontal red

lines appear in the display, disconnect power immediately. Recheck the range wiring connections.

If change is made to connections, retest again. If no change is required, have building wiring checked for

proper connections and voltage. It is recommended that the clock be changed if the red lines appear.

• Be sure all range controls are in the OFF position before leaving the range.

LEVEL THE RANGE (CONT.)

Position cord so that it does not interfere with drawer.

Place drawer rail on guides. Push the drawer in until it stops.

Lift front of drawer and push in until the stops clear

the guides.

Lower the front of the drawer and push in until it closes.

MODELS WITH BAKING, WARMING DRAWERS OR DOUBLE OVEN

Plug in the unit.

Measure the height of your countertop at the rear of the opening (X).

Adjust two rear leveling legs so that the rear of cooktop is at the same height

as the counter (Y).

Slide unit into place.

Install oven shelves in the oven and position the range where it will be installed.

Check for levelness by placing a spirit level on one of the oven shelves.

7DNHWZRUHDGLQJV³ZLWKWKHOHYHOSODFHGGLDJRQDOO\ILUVWLQRQHGLUHFWLRQ

and then the other.

Adjust front leveling legs until the range is level.

Leg

leveler

Lower

range

Raise

range

Spirit level

1 2 3 4 5 6 7 8

Commentaires sur ces manuels

Pas de commentaire

Hotpoint RA720KCT Manuel d'installation Page 4

Commentaires sur ces manuels