Hotpoint LI2JBA Manuel d'utilisateur télécharger pdf (Page 7)

Consult the designs in the front pages referenced in the text by alphabet

letters. Closely follow the instructions set out in this manual. All

responsibility, for any eventual inconveniences, damages or fires caused

by not complying with the instructions in this manual, is declined.

Installation

The cooker hood must be placed at a minimum distance of 60 cm from

the cooking plane for electric cookers and 70cm for gas or mixed

cookers. The hood can be installed above these heights but for

optimum performance it should be installed at the distance quoted for

the appropriate heat source.

Do not tile, grout or silicone this appliance to the wall. Surface

mounting only.

Do not fix chimney flue to furniture or fly over shelves unless the

chimney flue can be easily removed, in case maintenance is ever

required.

Use

The cooker hood is provided with an upper air exit B for discharging

fumes externally for models including chimney flue C ( Suction

Version A- exhaust pipe 13A not supplied).

In the instance where it is not possible to discharge cooking fumes and

vapours externally even if utilising the model with chimney flue C, the

cooker hood may be used in the filter version F by mounting two

active carbon filters E, the fumes and vapours are then recycled via

the upper grill G (depending on the model the grill may be directly

placed on the chimney flue or via the mounting of two small grills 

16F).

If in possession of a model with grill placed on chimney flue then two

H extensions must be placed on the deflector 13F.

The models provided with small dome D may only be used in the filter

version F.

The models without suction motor and the models with electric valve

only function in the suction version and must be connected to a

peripheral suction unit (not supplied).

Electrical connection

The electrical tension must correspond to the tension noted on the

label placed inside the cooker hood. Connect the electrical plug,

where provided, to the an easily accessible outlet in conformity with

local standards in force.

Where an electrical plug is not provided (for direct connection to

electrical network) place a standards approved bipolar switch with an

aperture distance of not less than 3mm (accessible) from the contacts.

Operation

The cooker hood is provided with a key or pushbutton control panel

situated of the frontal part of the cooker hood, depending on the basis

of the cooker hood type in possession. For proper operation consult

the text below and the relative illustration:

a. ON/OFF lighting

b. OFF motors/Valve

c. - d. - e. Minimum suction power/ON Valve (c.), medium (d.),

maximum (e.).

f. Operation warning light (where present).

Use the high suction speed in cases of concentrated kitchen vapours.

It is recommended that the cooker hood suction is switched on for 5

minutes prior to cooking and to leave in operation during cooking and

for another 15 minutes approximately after terminating cooking.

Only in the case of models with electric valve:

In this case the hood is provided with a control panel placed on the

front part of the hood with two keys, one for turning the lamp on and

off and one for opening and closing the valve.

Attention: opening and closing the valve is never immediate and takes

place after a brief lapse of time.

Model with electronic controls

1- Motor OFF button

2- ON button and motor speed selection button 1 - 2 - 3 - 1 - 2 - .

. . .

3- Speed 1 LED

4- Speed 2 LED and metal grease filter saturation LED (in this latter

case, the LED will flash - See instructions on grease filter

cleaning).

5- Speed 3 LED and active carbon filter saturation LED

(in this

latter case, the LED will flash - See instructions on active carbon

filter replacement).

Warning!

The active carbon filter saturation LED is not activated.

In order to activate the active carbon filter saturation indicator,

press buttons 2 and 7 simultaneously for 3 seconds. Initially,

only LED 4 will flash, then after the 3 seconds have passed, LED

5 will also start flashing, indicating that the active carbon filter

saturation control system is active.

To switch off the system, re-press the same two buttons: after

3 seconds LED 5 will stop flashing and the device will be

INSTRUCTION ON MOUNTING AND USE

a b-c

b-c-d-e

1 2 3 4 5 6 7 8 9 10 11 12

Commentaires sur ces manuels

Pas de commentaire

Hotpoint LI2JBA Manuel d'utilisateur Page 7

Commentaires sur ces manuels

Produits connexes et manuels pour Hottes de cuisine Hotpoint LI2JBA