Hotpoint BFV620K Mode d'emploi télécharger pdf (Page 13)

1509)50-4

Caution

- Do not forget that repairs should only be carried out by a qualified specialist. Improper repairs can lead to considerable

equipment damage, as well as danger to the user.

- The dishwasher must first be disconnected from the electricity supply before any repairs or other work can be carried

out. Switch off at the mains socket and water supply and remove the plug.

If the dishwasher won't

start, check...

■ Is the dishwasher plugged

in at the electricity socket

and switched on?

■ Is there a power failure,

check other appliances.

■ Check the fuse.

■ Is the water supply tap

turned on?

■ Is the water inlet hose

connected properly?

■ Is the pressure of the

water supply sufficient?

■ Is the inlet hose kinked?

■ Is the filter on the water

supply hose blocked?

■ Is the dishwasher door

not closed properly?

If water remains inside

the dishwasher, check...

■ the drain hose is not

kinked.

■ the drain syphon is not

obstructed.

■ the dishwasher filters are

not clogged.

If the dishes are not

being cleaned properly,

check...

■ the correct amount of

detergent has been added.

■ there is regenerating salt

in the salt container.

■ the dishes have been

loaded correctly.

■ the selected programme

is suitable for the type of

dishes and the degree of

soiling.

■ all filters are clean and

positioned correctly.

■ the spray arm nozzles are

not obstructed.

■ there is nothing

obstructing the rotation of

the spray arms.

If the dishes fail to dry or

remain dirty, check...

■ there is rinse aid inside the

rinse aid container.

■ the rinse aid dispenser

setting is correct.

■ the detergent being used

is of good quality and has

not lost its effectiveness

(for example, through

incorrect storage, with the

box left open).

If the dishes show signs

of streaking, staining etc.

check...

■ the rinse aid dispenser

setting is not set too high.

If there are visible traces

of rust inside the tank,

check...

■ the cap off the salt

container is securely

closed and that the water

softner setting is correct.

■ the correct amount of

detergent is being used.

Certain detergents can be

more corrosive than

others.

■ the tank is made of steel

and therefore any rust

marks are due to external

elements (fragments of

rust from the tank pipes,

pots, cutlery etc.) Special

products are

commercially available to

remove such marks.

Error messages

Your dishwasher is equipped

with a safety system which

is able to detect operating

faults.

These faults are reported by

one or two cycle phase indi-

cator lights "E" flashing rap-

idly. Take note of which

lights are flashing, turn the

appliance off and call

Hotpoint Service for techni-

cal assistance.

Tap off alarm

If you have forgotten to turn

the water tap on, your appli-

ance will remind you of this

by sounding a few short

beeps for a few minutes.

Turn the tap on and your ap-

pliance will start up again

after a few minutes. Were

you to be absent when these

beeps are sounded, the ap-

pliance will be blocked auto-

matically and cycle phase 2

and 3 indicator lights (wash

and rinse) will flash rapidly.

Turn the appliance off at the

ON-OFF button, turn on the

water tap and wait approxi-

mately 20 seconds before

turning the appliance back

on.

Re-select the wash cycle and

the appliance will start up

again.

Clogged filter alarm

If the appliance is blocked

and cycle phase1 and 3 indi-

cator lights (pre-wash and

rinses) flash rapidly, this

means the filter is clogged

by large particles of food resi-

due. Turn the appliance off,

clean the filter thoroughly

and reposition it in its seat

as illustrated on page 12.

Then turn the appliance back

on.

Re-select a wash cycle as

indicated in the "Selecting

the wash cycle" paragraph

and the appliance will start.

Water load solenoid

valve malfunction alarm.

If indicator light 2 (wash)

flashes rapidly, TURN the

dishwasher OFF AND

BACK ON AGAIN after

one minute. If the alarm

persists, first turn off the

water tap to avoid any

flooding and then cut off

the electricity supply and

call for technical

assistance.

If after all the checks, the

appliance still does not op-

erate or the problem per-

sists, call Hotpoint Service

(see KEY CONTACTS, back

page) and inform them of:

- the type of problem

- the abbreviation of the

model name (Mod.) and the

relative numbers (S/N) writ-

ten on the rating plate

located on the inner edge of

the door.

Switch off at the mains

socket and remove the plug.

Turn off the water supply.

Troubleshooting

Resolving minor problems yourself.

Experience has shown that you can resolve most problems that arise during normal daily usage yourself, without

having to call out a service engineer. Not only does this save costs but it also means the appliance is available for

use again that much sooner. The following list of common occurences and their remedies should help you identify the

causes of most problems.

1 2 ... 8 9 10 11 12 13 14 15 16

Commentaires sur ces manuels

Pas de commentaire

Hotpoint BFV620K Mode d'emploi Page 13

Commentaires sur ces manuels

Produits connexes et manuels pour Lave-vaisselle Hotpoint BFV620K