Hotpoint DFG 261B S AUS Mode d'emploi télécharger pdf (Page 12)

Rinse aid and refined salt

Only use products which have been specifically designed

for dishwashers.

Do not use table/industrial salt or washing-up liquid.

Follow the instructions given on the packaging.

If using a multi-functional product it is not necessary to add

any rinse aid. However, we recommend that you add salt,

especially if you live in an area where the water is hard or

very hard.

(Follow the instructions given on the packaging).

If you do not add salt or rinse aid, the LOW SALT* and

LOW RINSE AID indicator lights will stay lit.

Measuring out the rinse aid

Rinseaidmakesiteasierforthecrockerytodry,aswaterruns

off surfaces more readily and therefore does not leave streaks

or marks.

The rinse aid dispenser should be filled:

•WhentheLOWRINSEAID*indicatorlightonthecontrol

panel is illuminated;

1.Openthedispenserbyturningthe

lid (G) in an anticlockwise direction.

2. Pour in the rinse aid, making

sure it does not overflow from the

dispenser. If this happens, clean

the spill immediately with a dry cloth.

3. Screw the lid back on.

NEVER pour the rinse aid directly

into the appliance tub.

Adjusting the amount of rinse aid

If you are not completely satisfied with the drying results, you

mayadjustthequantityofrinseaidused.Useascrewdriverto

turn the dosage adjuster (F) to one of the 6 pre-set positions

(the default position is set to 4):

•Iftherearestreaksonthecrockery,settheadjustmentdevice

toalowernumber(1-3).

•Ifdropsofwaterremainonthecrockeryoriftherearelimescale

marks present after the cycle has finished, set the adjuster to

a higher number (4-6).

Setting the water hardness

Everydishwasherisequippedwithawatersoftenerwhich,by

using refined salt designed especially for this type of appliance,

supplies water without limescale which is then used to wash

the crockery.

This dishwasher offers a setting which helps to reduce pollution

and optimises washing performance in accordance with the wa-

ter hardness level in your area. This information can be obtained

from the organisation which supplies your household with water.

- Switch the machine off using the ON/OFF button and open

the door.

- Set the SELECT WASH CYCLE knob first to wash cycle 5,

then to wash cycle 1, then to wash cycle 5 again.

- Press the ON/OFF button; the wash cycle phase (washing,

drying, end) indicator lights will flash. It is now possible to select

the water hardness level. There is a water hardness level for

every wash cycle:

E.g.:washcycle1,waterhardnesslevel1

washcycle2,waterhardnesslevel2,etc.etc.,uptoamaximum

of 5* levels.

(The default water softener setting is level 3).

- To exit the function, wait a few seconds or press one of the op-

tion buttons*, or switch off the machine using the ON/OFF button.

Evenifusingmulti-functionaltablets,thesaltdispensershould

still be filled.

(°dH=hardnessmeasuredinGermandegrees-°f=hardness

measuredinFrenchdegrees–mmol/l=millimolesperlitre)

Measuring out the refined salt

In order to obtain the best possible results from a wash cycle,

make sure that the salt dispenser is never empty.

Refinedsaltremoveslimescalefromthewater,thusavoiding

the formation of deposits on crockery.

The salt dispenser is located in the lower part of the dishwasher

(see Description)

and should be filled:

• Whenthegreenfloat* cannot be seen by simply looking at

the cap of the salt dispenser;

• WhentheLOWRINSEAIDindicatorlightonthecontrolpanel

is illuminated *;

1.Removethe lowerrackandunscrew

the cap (anticlockwise).

2.Thefirsttimeyoudothis:fillthewater

tank right up to its edge.

3. Position the funnel*

(see figure)

and

fill the salt dispenser up to the edge

(approximately 1 kg). It is normal for a

little water to leak out.

4.Removethefunnel*andwipeanysaltresiduesawayfrom

the opening; rinse the cap under running water and then screw

it on, the head facing downwards so as to let the water flow out

of the four slots (star-shaped arrangement) in the lower part of

the cap (cap with green float*).

It is advisable to perform this procedure every time you add

salt to the dispenser.

Make sure the cap is screwed on tightly so that no detergent can

get into the container during the wash cycle (this could damage

the water softener beyond repair).

Whennecessary,measureoutthesaltbeforeawashcycle

so that any saline solution which has leaked out of the salt

dispenser is removed.

* Only available in selected models.

Water Hardness Table

Average salt dispenser

capacity duration**

level °dH °fH mmol/l months

1 0 - 6 0 - 10 0 - 1 7 months

2 6 - 11 11 - 20 1,1 - 2 5 months

3 12 - 17 21 - 30 2,1 - 3 3 months

4 17 - 34 31 - 60 3,1 - 6 2 months

34 - 50 61 - 90 6,1 - 9 2/3 weeks

For values between 0°f and 10°f, we do not recommend the use of salt.

* a setting of 5 may increase cycle duration.

** 1 wash cycle per day.

1 2 ... 7 8 9 10 11 12 13 14 15 16

Commentaires sur ces manuels

Pas de commentaire

Hotpoint DFG 261B S AUS Mode d'emploi Page 12

Commentaires sur ces manuels

Produits connexes et manuels pour Lave-vaisselle Hotpoint DFG 261B S AUS