Hotpoint FDFAO 32121 X Mode d'emploi télécharger pdf (Page 4)

If the appliance must be moved at any time, keep it in an

upright position; if absolutely necessary, it may be tilted onto

its back.

Positioning and levelling

1. Position the dishwasher on a level sturdy floor. If the floor is

uneven, the front feet of the appliance may be adjusted until

it reaches a horizontal position. If the appliance is levelled

correctly, it will be more stable and much less likely to move

or cause vibrations and noise while it is operating.

2. Before recessing the dishwasher, stick the adhesive

transparent strip* under the wooden shelf in order to protect

it from any condensation which may form.

3. Place the dishwasher so that its sides or back panel are in

contact with the adjacent cabinets or the wall. This appliance

can also be recessed under a single worktop*

(see the

Assembly instruction sheet)

4*. To adjust the height of the rear foot, turn the red hexagonal

bushing on the lower central part at the front of the dishwasher

using a hexagonal spanner with an opening of 8 mm. Turn the

spanner in a clockwise direction to increase the height and

in an anticlockwise direction to decrease it.

(see Building-in

instruction sheet attached to the documentation)

The dishwasher meets the requirements set out by the regulations

in force concerning safety and electrical equipment.

Any technical checks should be conducted exclusively by a

trained and authorised technician: Repairs carried out by

unaithorised persons will invalidate the guarantee, as well as

posing a potential hazard to the user.

The manufacturer declines all responsibility for damage to

persons or property resulting from failure to observe the above

precautions, from tampering with even a single component or

from the use of non-original spare parts.

Connecting the water supply

Adaptation of the water supply for installation should only

be performed by a qualified technician.

The water inlet and outlet hoses may be positioned towards

the right or the left in order to achieve the best possible

installation.

Make sure the dishwasher does not bend or squash the hoses.

Connecting the water inlet hose

• To a 3/4” gas cold or hot water connection point (max.

60°C).

• Run the water until it is perfectly clear.

• Screw the inlet hose tightly into position and turn off the

tap.

If the inlet hose is not long enough, contact a specialist

store or an authorised technician

(See Repairs and After

Sales)

The water pressure must be within the values indicated

in the Technical Data table - otherwise the dishwasher may

be function properly.

Make sure the hose is not bent, compressed or kinked.

DO NOT overtighten the hose connector, hand tight is

sufficient.

Tap connections*: A range of adaptors are available to

suit your tap.

Connecting the drain hose

Connect the drain hose (without bending) to a drain duct with

a minimum diameter of 2 cm. (A)

The drain hose connection must be at a height ranging from

40 to 80 cm (from 15’’ to 31’’) from the floor or surface where

the dishwasher rests.

• before connecting the drain hose, remove any internal

restrictions; this will prevent a build up of debris which

could cause a blockage.

• remove any restrictions from the waste spigot and ensure

that the sealing bung is removed (B).

It MUST NOT be connected to a surface water drain.

Ensure the drain hose is securely

attached, to prevent it coming away

while the machine is in use and

causing a flood.

Fit hose to waste securely using

a “Jubilee” type clip.

Anti-flooding protection

To ensure floods do not occur, the dishwasher:

- is provided with a special system which blocks the water

supply in the event of anomalies or leaks from inside the

appliance.

Some models are also equipped with the supplementary

safety device New Acqua Stop*, which guarantees anti-

flooding protection even in the event of a supply hose rupture.

WARNING: HAZARDOUS VOLTAGE!

Under no circumstances should the water inlet hose be cut

as it contains live electrical parts.

Installation

MIN 40 cm

MAX 80 cm

* Only available in selected models.

1 2 3 4 5 6 7 8 9 ... 15 16

Commentaires sur ces manuels

Pas de commentaire

Hotpoint FDFAO 32121 X Mode d'emploi Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Lave-vaisselle Hotpoint FDFAO 32121 X