Hotpoint LBF 52 TK/HA.R Mode d'emploi télécharger pdf (Page 18)

Start-up and use

Measuring out the detergent

A good wash result also depends on the correct amount

of detergent being used; exceeding the stated amount

does not result in a more effective wash and increases

environmental pollution.

Only use detergent which has been specifically

designed for dishwashers.

DO NOT USE washing up liquid.

Using excessive detergent may result in foam

residue remaining in the machine after the cycle has

ended.

The use of tablets is only recommended for models

which offer the MULTI-FUNCTIONAL TABLETS

option.

To achieve the best results from each washing and

drying cycle, powder detergent, rinse aid liquid and salt

should be used.

Compartment A: Washing detergent

Compartment B: Pre-wash detergent

1. Open cover C by pressing button

2. Pour in the detergent after

consulting the

Table of wash cycles

• For powder detergent use

compartments A and B.

• For detergent in tablet form: when

the cycle requires 1 tablet, place it

in compartment A and close the cover; when it requires 2,

place the second tablet at the bottom of the appliance.

3. Remove detergent residues from the edges of the

compartment and close the cover until it clicks.

* Only available in selected models.

Starting the dishwasher

1. Turn the water tap on.

2. Press the ON/OFF button: all the indicator lights on the

control panel will light up for a few seconds.

3. Open the door and pour in a suitable amount of detergent

(

see below

4. Load the racks (

see Loading the racks

) and shut the

door.

5. Select the wash cycle by turning the WASH CYCLE

SELECT knob in a clockwise direction: align the notch on

the knob with the number or symbol representing the

desired wash cycle. The START/PAUSE indicator light will

flash.

6. Select the wash options

* (

see adjacent information

7. Start the cycle by pressing the START button; the

indicator light will light up and remain lit in a fixed manner.

The indicator light corresponding to the wash phase will

switch on, signalling that the wash cycle has begun.

8. At the end of the wash cycle the END indicator light will

switch on (fixed light). Switch off the appliance by pressing

the ON/OFF button, shut off the water valve and unplug

the appliance from the electricity socket.

9. Wait for a few minutes before removing the crockery, in

order to avoid burns. Unload the racks, beginning with the

lower level.

- The machine will switch off automatically during

certain periods of inactivity, in order to minimise

electricity consumption.

Modifying a wash cycle in progress

If a mistake was made during the wash cycle selection

process it is possible to change the cycle, provided that it

has only just begun: once the wash cycle has started, switch

off the machine by pressing and holding the ON/OFF/Reset

button. Switch it back on using the same button and select

the desired wash cycle and options.

Adding extra crockery

Press the Start/Pause button (the corresponding indicator light

will flash). Open the door, taking care to avoid the escaping

steam, and place the crockery inside the appliance. Press

the Start/Pause button (fixed light): the cycle starts from the

point at which it was interrupted.

If the Start/Pause button is pressed so as to pause the

machine, the wash cycle or the Delayed Start function

(if selected) is interrupted.

At this stage it is not possible to change the wash cycle.

Accidental interruptions

If the door is opened during the wash cycle, or if there is a

power cut, the cycle stops. It starts again from the point at

which it was interrupted once the door has been shut or once

the electricity supply is restored.

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 24

Commentaires sur ces manuels

Pas de commentaire

Hotpoint LBF 52 TK/HA.R Mode d'emploi Page 18

Commentaires sur ces manuels

Produits connexes et manuels pour Lave-vaisselle Hotpoint LBF 52 TK/HA.R