Hotpoint LSTB 6B00 UK Mode d'emploi Page 10

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 16
  • Table des matières
  • DEPANNAGE
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 9
10
GB
Detergent and
dishwasher use
Measuring out the detergent
Good washing results also depend on the correct amount of
detergent being used. Exceeding the stated amount does not
result in a more effective wash and increases environmental
pollution.
The amount can be adjusted to the soil level.
In the case of normally soiled items, use approximately either
25g (powder detergent) or 25ml (liquid detergent). If tablets
are used, one tablet will be enough.
If the crockery is only lightly soiled or if it has been rinsed
with water before being placed in the dishwasher, reduce the
amount of detergent used accordingly.
For good washing results also follow the instructions shown
on the detergent box.
For further questions please ask the detergent producers.
Open the detergent dispenser using button D and measure out
the detergent according to the Table of wash cycles:
powder or liquid: compartments
A (wash detergent) and B (pre-
wash detergent)
tablets: when the cycle requires
1 tablet, place it in compartment
A and close cover C; when it
requires 2 tablets, place the
second tablet on the bottom of
the appliance.
Remove detergent residues from
the edges of the compartment and close cover C until it clicks.
The detergent dispenser automatically opens up at the right time
according to the wash cycle.
If all-in-one detergents are used, we recommend using the TABS
option, because it adjusts the cycle so that the best washing and
drying results are always achieved.
Only use detergent which has been specifically designed
for dishwashers.
DO NOT USE washing up liquid.
Using excessive detergent may result in foam residues
remaining in the machine after the cycle has ended.
To achieve the best washing and drying results, the combined
use of detergent, rinse aid liquid and refined salt is required.
We recommend using detergents that do not contain
phosphates or chlorine, as these products are harmful
to the environment.
* Only available in selected models.
Starting the dishwasher
1. Turn the water tap on.
2. Open the door and press the ON/OFF button.
3. Measure out the detergent.
(see adjacent information).
4. Load the racks (
see Loading the racks
).
5. Select the wash cycle in accordance with the type of crockery
and its soil level
(see Table of wash cycles)
by pressing the P
button.
6. Select the wash options*.
(see Special wash cycles and
Options)
.
7. Start the wash cycle by shutting the door.
8. The end of the wash cycle is indicated by beeps and by the
flashing of the indicator light of the selected wash cycle. Open
the door, switch off the appliance by pressing the ON/OFF
button, shut off the water tap and unplug the appliance from the
electricity socket.
9. Wait a few minutes before removing the crockery in order to
avoid burns. Unload the racks, beginning with the lower level.
The machine will switch off automatically during
long periods of inactivity in order to minimise electricity
consumption.
If the crockery is only lightly soiled or if it has been rinsed
with water before being placed in the dishwasher, reduce the
amount of detergent used accordingly.
Changing a wash cycle in progress
If a mistake was made in the wash cycle selection process, it
is possible to change the cycle provided that it has only just
begun: open the door, taking care to avoid the escaping steam,
and press and hold the ON/OFF button; the machine will switch
off. Switch the machine back on using the ON/OFF button and
select the new wash cycle and any options desired; start the
cycle by closing the door.
Adding extra crockery
Without switching off the machine, open the door, taking care
to avoid the escaping steam, and place the crockery inside the
dishwasher. Close the door: the cycle starts from the point at
which it was interrupted.
Accidental interruptions
If the door is opened during the wash cycle or there is a power
cut, the cycle stops. It starts again from the point at which it
was interrupted once the door has been shut or the electricity
supply restored.
Vue de la page 9
1 2 ... 5 6 7 8 9 10 11 12 13 14 15 16

Commentaires sur ces manuels

Pas de commentaire