Hotpoint PFT 8H4 X TW Mode d'emploi télécharger pdf (Page 2)

Keep this instruction manual in a safe place for future

reference. If the appliance is sold, given away or moved,

please ensure the manual is kept with the machine, so that

the new owner may benefit from the advice contained within

it.

Please read this instruction manual carefully: it contains

important information regarding the safe installation, use and

maintenance of the appliance.

If the appliance must be moved at any time, keep it in an

upright position; if absolutely necessary, it may be tilted onto

its back.

This appliance is designed for domestic use or similar

applications, for example:

- staff kitchen areas in shops, offices and other work

environments;

- farmhouses;

- use by guests in hotels, motels and other residential settings;

- bed and breakfasts.

Positioning and levelling

1. Remove the appliance from all packaging and check that it

has not been damaged during transportation.

If it has been damaged, contact the retailer and do not

proceed any further with the installation process.

2. Check the dishwasher by placing it so that its sides or back

panel are in contact with the adjacent cabinets or even with

the wall. This appliance can also be recessed under a single

worktop

(see the Assembly instruction sheet).

3. Position the dishwasher on a level and sturdy floor. If the

floor is uneven, the front feet of the appliance may be adjusted

until it reaches a horizontal position. If the appliance is levelled

correctly, it will be more stable and much less likely to move

or cause vibrations and noise while it is operating.

*. To adjust the height of the rear foot, turn the red hexagonal

bushing on the lower central part at the front of the dishwasher

using a hexagonal spanner with an opening of 8 mm. Turn

the spanner in a clockwise direction to increase the height

and in an anticlockwise direction to decrease it.

(see Building-

in instruction sheet attached to the documentation)

Connecting the water and electricity

supplies

Connection to the water and electricity supplies should

only be performed by a qualified technician.

The dishwasher should not stand on top of the water hoses

or the electricity supply cable.

The appliance must be connected to the water supply

network using new piping.

Do not use old piping.

The water inlet and outlet hoses and the electricity supply

cable may be positioned towards the right or the left in order

to achieve the best possible installation.

Connecting the water inlet hose

• To a suitable cold water connection point: before attaching

the hose, run the water until it is perfectly clear so that any

impurities that may be present in the water do not clog the

appliance; after performing this operation, screw the inlet hose

tightly onto a tap with a ¾ gas threaded connection.

• To a suitable hot water connection point: your dishwasher

may be supplied with hot water from the mains supply (if you

have a central heating system with radiators) provided that it

does not exceed a temperature of 60°C.

Screw the hose to the tap as described for connection to a

cold water supply.

If the inlet hose is not long enough, contact a specialist

store or an authorised technician (

see Assistance

The water pressure must be within the values indicated

in the Technical data table (

see adjacent information

The hose should not be bent or compressed.

Connecting the water outlet hose

Connect the outlet hose (without bending it) to a drain duct

with a minimum diameter of 4 cm.

The outlet hose must be at a height ranging from 40 to 80 cm

from the floor / surface where the dishwasher rests (A).

Before connecting the water outlet hose to the sink drain,

remove the plastic plug (B).

Anti-flooding protection

To ensure floods do not occur, the dishwasher:

- is fitted with a special system which blocks the water supply

in the event of malfunctions or leaks from inside the appliance.

Some models are also equipped with the supplementary

New

Acqua Stop

* safety device, which guarantees anti-flooding

protection even in the event of a supply hose rupture.

WARNING: HAZARDOUS VOLTAGE!

Under no circumstances should the water inlet hose be cut

as it contains live electrical parts.

* Only available in selected models.

Installation

1 2 3 4 5 6 7 ... 27 28

Commentaires sur ces manuels

Pas de commentaire

Hotpoint PFT 8H4 X TW Mode d'emploi Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Lave-vaisselle Hotpoint PFT 8H4 X TW