Hotpoint CTD80 Manuel d'utilisateur télécharger pdf (Page 6)

Choosing a programme

1. Plug the dryer into the electrical socket.

2. Sort your laundry according to fabric type (see

Laundry).

3. Open the door and make sure the filter is clean

and in place and that the water container is

empty and in place (see Maintenance).

4. Load the machine and make sure items are not

in the way of the door seal. Close the door.

5. If the On/Off light is not lit: Press the ON/OFF

button .

6. Press the Programme selection button that

corresponds to the fabric type being dried by

checking the Programmes table (see Programmes)

as well as the indications for each type of fabric

(see Laundry).

- Select either the option button for Timed Drying

or, if available ‘Set & Forget’ Drying (most

programmes default to the Set & Forget setting)

see Programmes table.

7. Set a delay time and other options if necessary.

8. If you wish to select the buzzer sound, at the end

of the progamme, press the ALARM Option button.

9. Press the START button to begin. The display will

show the estimated time to end.

During the drying programme, you can check on

your laundry and take out items that are dry

while others continue drying. When you close

the door again, press the START button in order

to resume drying.

10. During the last few minutes of Drying

Programmes, before the programme is

completed, the final COOL TUMBLE phase

is entered (fabrics are cooled),

this phase should always be allowed to complete.

11. The buzzer (if Alarm Option was selected) will

warn you when the programme is complete and

the display shows .

Open the door, take the laundry out, clean the filter

and replace it. Empty the water container and

replace it (see Maintenance).

If the Post Care Option has been selected

and you do not remove the laundry immediately,

the dryer will tumble occasionally for 10 hours

or until you open the door.

12. Unplug the dryer.

Start and Programmes

Easy Iron Programme

‘Easy Iron’ is a short 10 minute programme (8 minutes of heat followed by a 2 minute cool tumble period) which

fluffs the fibres of clothing that have been left in the same position/location for an extended period of time. The

cycle relaxes the fibres and makes them easier to iron and fold.

! ‘Easy Iron’ is not a drying programme and should not be used for wet articles of clothing.

For best results:

1. Do not load more than the maximum capacity. These numbers refer to the dry weight:

Fabric Maximum load

Cotton and Cotton mixtures 2.5kg

Synthetics 2kg

Denim 2kg

2. Unload the dryer immediately after the end of the programme, hang, fold or iron the articles and put

them away in the closet. Should this not be possible repeat the programme.

The ‘Easy Iron’ effect varies from one fabric to the next. It works well on traditional fabrics like Cotton or Cotton

mix, and less well on acrylic fibres and on materials such as Tencel®.

Wool Programme

●

This is a programme for tumble dryer safe garments marked with the symbol .

●

It can be used for load sizes up to 1kg (approximately 3 sweaters).

●

We recommend that garments are turned inside out before drying.

●

This programme will take about 20 to 40 minutes, but may take longer depending on the size and density of

the load and the spin speed used in your washer.

●

Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may

be slightly damp. Allow these to dry naturally as over-drying could damage garments.

! Unlike other materials, the mechanism of wool shrinkage is irreversible; i.e. it will not stretch back to original

size and shape.

! This programme is not suitable for Acrylic garments.

E88

1 2 3 4 5 6 7 8 9 10 11 ... 15 16

Commentaires sur ces manuels

Pas de commentaire

Hotpoint CTD80 Manuel d'utilisateur Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Séchoirs Hotpoint CTD80