Hotpoint AKM 613/IX/01 Mode d'emploi télécharger pdf (Page 3)

Fig. 1

Fig.

ig. 3

INSTALLATION

RECOMMENDATIONS

Important: Disconnect the hob from the mains before carrying out any

installation work or servicing.

• All electrical connections must be made before connecting the appliance

to the power supply.

• Installation must be carried out by a qualied technician in accordance

with the manufacturer’s instructions and in compliance with local

regulations.

• Unpack the hob and make sure that the appliance has not been damaged

during transport. If you are not sure contact the dealer or the nearest

service centre.

PREPARING THE HOUSING UNIT

• Cut the worktop to t before installing the appliance. Carefully remove

any shavings or sawdust that could prevent the appliance from running

properly.

Attention: to install the hob on other surfaces than wood (marble, plastic,

ceramic, marble, stone, etc.) remember to ask After Sales Service for the

xing plates (g. 2) Code 4819 404 78697.

• The hob must be tted in a worktop with a minimum thickness of 20 mm

and a maximum of 50 mm.

• Insert a separator panel at a minimum distance of 90 mm from the bottom

of the hob, so that it cannot be accessed by the user.

• If there is an oven under the hob, make sure that it is manufactured by

us and equipped with a cooling system.

• There must be nothing between the hob and the oven (e.g. cables,

insulating material, etc.).

• An adjacent column unit must be installed at least 100 mm from the

edge of the hob.

• Cut an opening in the worktop of the given dimensions.

• We recommend you seal the internal edges of the worktop with wood

glue or silicone.

• If not already in place, apply the supplied seal to the hob, after cleaning

the adhesive surface thoroughly.

GLASS-CERAMIC HOB

Important: remove any protective lm before installing the hob.

Make sure that that the opening in the worktop for the hob is cut according to

the dimensions given in the drawing, paying attention to the tolerance range.

The hob should not be forced into the worktop. Forcing the glass-ceramic

top may cause it to crack (even at a later date)!

• If the worktop is made of wood, use the spring clips and screws

provided.

1. Secure the spring clips (A) (g. 1) with the screws provided (B) (g.

1) as shown, paying attention to the specied distances.

2. Fit the hob into the worktop.

• If the worktop is made of marble, plastic, ceramic, stone, etc., the

hob must be secured with special brackets (C) (g. 2).

1. Fit the hob into the worktop (g. 1).

2. Place the 4 brackets (C) in position in accordance with the thickness

of the worktop as shown in g. 2.

3. Fasten the 4 screws (D) in the positions (E) (g. 2).

ELECTRICAL CONNECTION

• Regulations require that the appliance be earthed.

• Connection to the mains must be carried out by a qualied technician

in accordance with the manufacturer’s instructions and in compliance

with local regulations.

• The installer is responsible for connecting appliances correctly to the

mains and for observing the safety regulations.

• The oven power cable must be long enough to connect the built-in

appliance to the mains.

• Observance of safety directives requires that a multipole switch with a

minimum contact gap of 3 mm be used for the installation.

• Do not use multiple plug adapters or extension leads.

• After the oven has been installed, the electrical components must be

inaccessible.

CONNECTING THE OVEN TO THE POWER SUPPLY

Note: the yellow/green earth wire must be connected to the screw with the

symbol .

• Strip approx. 70 mm of the cable sheath from the power supply cable (G).

• Strip approx. 10 mm of sheath from the conductors. Insert the cable (G)

through the opening in the lid (F).

• Insert the cable into the cable clamp and connect the conductors to the

terminal block as indicated in the diagram printed on the lid.

• Secure the power cable (G) by means of the cable clamp.

• Ret the protection lid (F).

• After the electrical connection, t the hob from the top and hook it to the

xing springs, according to the illustration.

DECLARATION OF CONFORMITY

This cooktop is suitable for contact with foodstuffs and complies with EEC

(CE) Regulation n. 1935/2004.

This hob (Class Y) has been designed to be used only for cooking. Any other

use (such as heating a room) is improper and dangerous.

This hob has been designed, constructed and marketed in compliance with:

• safety objectives of the “Low Voltage” Directive 2006/95/EC (which

replaces 73/23/EEC and subsequent amendments);

• the protection requirements of Directive “EMC” 2004/108/EC;

• requirements of EEC Directive 93/68.

The Manufacturer reserves the right to change product specications without

prior notice.

1 2 3

Commentaires sur ces manuels

Pas de commentaire

Hotpoint AKM 613/IX/01 Mode d'emploi Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Plaques chauffantes Hotpoint AKM 613/IX/01