Hotpoint CIO 644 DD Z Mode d'emploi télécharger pdf (Page 3)

Fixing

The appliance must be installed on a perfectly level

supporting surface.

Any deformities caused by improper fixing could affect

the features and operation of the hob.

The thickness of the supporting surface

should be

taken into account when choosing

the length of the

screws for the fixing hooks:

 30 mm thick: 23 mm screws

 40 mm thick: 13 mm screws

Fix the hob as follows:

1. Use short flat-bottomed screws to fix the 4

alignment springs in the holes provided at the central

point of each side of the hob.

2. Place

the hob in the cavity, make sure it is in a

central position and push down on the whole perimeter

until the hob is stuck to the supporting surface.

3. For hobs with raised sides: After inserting the hob

into its cavity, insert the 4 fixing hooks (each has its

own pin) into the

lower edges of the hob, using the

long pointed screws to fix them in place, until the

glass is stuck to the supporting surface.

 The screws for the alignment springs must remain

accessible.

 In order to adhere to safety standards, the appliance

must not come into contact with electrical parts once it

has been installed.

 All parts which ensure the safe operation of the

appliance must not be removable without the aid of a

tool.

Electrical connection

 The electrical connection for the hob and for any built-

in oven must be carried out separately, both for safety

purposes and to make extracting the oven easier.

Single-phase connection

The hob is equipped with a pre-connected electricity

supply cable, which is designed for single-phase

connection. Connect the wires in accordance with the

instructions given in the following table and diagrams:

Voltage and

mains frequency

Electrical cable Wire connection

220-240V 1+N ~

50 Hz

: yellow/green;

N: the two blue wires

together

L: brown and black

together

Other types of connection

If the mains supply corresponds with one of the

following:

Voltage and mains frequency

 400V - 2+N ~ 50 Hz

 220-240V 3 ~ 50 Hz

 400V 3 - N ~ 50 Hz

 400V - 2+2N ~ 50 Hz

Separate the wires and connect them in accordance

with the instructions given in the following table and

diagrams:

Voltage and

mains frequency

Electrical cable Wire connection

400V - 2+N ~

50 Hz

220-240V 3 ~

50Hz

400V 3-N~ 50Hz

: yellow/green;

N: the two blue wires together

L1: black

L2: brown

400V - 2+2N ~

50 Hz

: yellow/green;

N1: blue

N2: blue

L1: black

L2: brown

Connecting the electricity supply cable to the mains

If the appliance is being connected directly to the

electricity mains an omnipolar switch must be installed

with a minimum opening of 3 mm between contacts.

 The installer must ensure that the correct electrical

connection has been made and that it is fully

compliant with safety regulations.

Before connecting the appliance to the power supply,

make sure that:

 The appliance is earthed and the plug is compliant

with the law.

 The socket can withstand the maximum power of the

appliance, which is indicated on the data plate

located on the appliance itself.

 The voltage falls within the range of values indicated

on the data plate.

 The socket is compatible with the plug of the

appliance. If the socket is incompatible with the

plug, ask an authorised technician to replace it. Do

not use extension cords or multiple sockets.

 Once the appliance has been installed, the power

supply cable and the electrical socket must be easily

accessible.

 The cable must not be bent or compressed.

 The cable must be checked regularly and replaced

by authorised technicians only.

 The manufacturer declines any liability should

these safety measures not be observed.

 Do not remove or replace the power supply cable for

any reason. Its removal or replacement will void the

warranty and the CE marking. INDESIT does not

assume liability for accidents or damage arising from

replacement/removal of the original power supply

cable. Replacement can only be accepted when

carried out by personnel authorised by INDESIT and

using an original spare part.

1 2 3 4 5 6 7 8 ... 15 16

Commentaires sur ces manuels

Pas de commentaire

Hotpoint CIO 644 DD Z Mode d'emploi Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Plaques chauffantes Hotpoint CIO 644 DD Z