Hotpoint MN 313 IX HA Guide d'utilisation et d'entretien Page 5

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 21
  • Table des matières
  • DEPANNAGE
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 4
EN
5
After unpacking the appliance,
make sure that it has not been
damaged during transport. In the
event of problems, contact the
dealer or your nearest After-sales
Service.
The appliance must be
disconnected from the mains
before starting installation.
During installation, make sure the
appliance does not damage the
power cable.
Do not switch on the appliance
until installation is complete.
This appliance is intended to be
used built-in. Do not use it free-
standing.
Carry out all cabinet cutting
works before tting the
appliance in the furniture and
carefully remove all wood chips
and sawdust.
After installation, the bottom of
the appliance must no longer be
accessible.
Do not obstruct the minimum
gap between the worktop and
the upper edge of the oven.
Only remove the oven from its
polystyrene foam base at the
time of installation.
After unpacking the appliance,
make sure that the appliance
door closes properly.
In the event of problems, contact
the dealer or your nearest After-
sales Service.
ELECTRICAL WARNINGS
For installation to comply with
current safety regulations, the
appliance must be earthed and
tted with an all-pole disconnect
switch with a minimum gap of 3
mm between the contacts.
If the tted plug is not suitable
for your socket outlet, contact a
qualied technician.
The power cable must be long
enough to connect the
appliance, once tted in its
housing, to the mains power
supply. Do not pull the power
supply cable.
If the power cable is damaged,
replace with an identical one. The
power cable must only be
replaced by a qualied technician
in compliance with the
manufacturer instruction and
current safety regulations.
Contact an authorized service
center.
For appliances with tted plug, if
the plug is not suitable for you
socket outlet, contact a qualied
technician.
Do not use extension leads,
multiple sockets or adapters.
Do not operate the appliance if it
has a damaged power cable or
plug, if it is not working properly,
or if it has been damaged or
dropped. Keep the cord away
from hot surfaces.
The electrical components must
not be accessible to the user after
installation.
Do not touch the appliance with
wet hands and do not operate it
when barefoot.
The rating plate is on the front
edge of the oven (visible when
the door is open).
If you need to replace the power
cable, contact an authorised
Technical After-sales Service
Centre.
It must be possible to disconnect
the appliance from the mains by
unplugging it (if the plug is
accessible) or by using a multi-
pole switch that has been
installed in an accessible place
upstream of the socket in
compliance with national
electrical safety standards.
CLEANING AND MAINTENANCE
Wear protective gloves for
cleaning and maintenance.
The appliance must be
disconnected from the mains
before performing maintenance
work.
Never use steam cleaning
equipment.
WARNING: It is dangerous for
anyone other than a qualied
person to carry out any service or
repair work that involves
removing the cover panels, as
these cover panels provide
protection against exposure to
microwave energy.
WARNING: Make sure that the
appliance is switched o before
replacing the lamp to avoid the
possibility of electric shock.
Failure to clean the oven regularly
may cause the surface to
deteriorate, which could have an
adverse eect on the service life
of the appliance and potentially
result in hazardous situations.
The oven shall be cleaned
regularly and any food deposits
removed.
Make sure that the appliance has
cooled down before carrying out
any maintenance or cleaning.
Do not use harsh abrasive
cleaners or sharp metal scrapers
to clean the door glass since they
can scratch the surface, which
may result in shattering of the
glass.
Vue de la page 4
1 2 3 4 5 6 7 8 9 10 ... 20 21

Commentaires sur ces manuels

Pas de commentaire