Hotpoint TCUD 93B 6P/Z (UK) Mode d'emploi télécharger pdf (Page 11)

Important

Information Installation Description The Display

Start and

Programmes Laundry

Warnings and

Suggestions Troubleshooting Service

Maintenance

and Care

Start and Programmes

Timed Drying

Timed Dry programmes table: First select a programme (see Programmes Table).

(0:20, 0:30,

1:00, 1:30, 2:00,

2:40 or 3:00

Hours:Minutes)

Always use Timed Drying

for loads less than 1kg, or

if you prefer a different

dryness result.

The heat settings available

depend on the programme

selected.

Use on low heat setting for

Acrylics and delicate materials

(see Laundry).

Consult suggested drying

times (see Laundry).

The last 10 minutes of these

programmes is the Cool

Tumble phase.

1. Press and release the button until the

display shows the required selection. Each

press advances , , , , ,

, then and then repeats.

●

Delicates have maximum time of

●

When is displayed, Automatic

Dryness Level option is available if you

change your mind.

2. Select any Options if required.

3. Press the Start button .

Options available:

! Warning, after pressing the Start/Pause button , the

programme cannot be changed.

To change a selected programme, press the Start/Pause

button , the light flashes Amber to indicate the

programme is paused. Select the new programme and

any options required, the light will then flash green.

Press the Start/Pause button again and the new

programme will start.

●

Option buttons

These buttons are used to customise the selected

programme to your requirements. A programme must

have been selected, by pressing a programme selection

button, before an option can be selected. Not all options

are available for all programmes (see Programmes Table).

If an option is not available and you press the button, the

buzzer will beep 3 times. If the option is available the

indicator, on the display unit above the bottom buttons,

lights to show that the option has been selected.

Time Delay (Delay Timer)

The start of some programmes (see The Display and

Programmes tables) can be delayed for up to 24 hours.

Ensure the water container is emptied before setting a

delayed start.

Crease Care

The pre-care option is only available if a delayed start has

been selected. It tumbles the clothes occasionally during the

delayed period to help prevent creases developing.

The post-care option occasionally tumbles the clothes after

end of the drying and cool tumble cycles to prevent creases

developing, should you not be available to remove the load

immediately the programme is complete. Note: The

Start/Pause light flashes Amber during this phase.

Selecting this option enables both the pre and post care

functions if appropriate.

High Heat

Allows Low Heat to be selected on some programmes.

When the light above this button is on High Heat is

selected. Not all programmes allow you to change this

setting. When High Heat is selected with the Refresh

programme this selects the Heat & Enjoy cycle.

Sound

Available on all programmes and allows the buzzer to

give a signal at the end of the drying cycle, to remind

you that the clothes are ready to be removed.

●

TIME DISPLAY

The display shows either the amount of time delay

remaining or an indication of the amount of time left for a

drying programme (see The Display).

The delay or time to end is displayed in hours and

minutes and counts down each minute.

The Controls

88:88

When timed programmes are selected the time displayed

throughout the cycle is the actual time remaining.

When an Automatic programme is selected, the time

displayed is an estimate of the time remaining. When the

programme is selected the display shows the time

required to dry a full load, after around 10 minutes the

controller calculates a better estimate of the cycle time.

The colons between the hours and minutes in the display

flash to show that the time is counting down.

The display also shows if there is a problem with your

dryer, if this occurs the display will show F followed by a

fault code number (see Troubleshooting).

●

Empty Water Container

(If you have plumbed your dryer to a drain this icon can be

ignored, as there is no need to empty the water container).

Messages are displayed to reminds you to empty the

water container (see The Display).

If the water container fills during a programme, the heater

turns off and the dryer does a period of Cool Tumble.

After this it stops and a message tells you to

EMPTY THE WATER CONTAINER .

You must empty the water container and restart the dryer

or the clothes will not dry. After re-starting the dryer the

message will take a few seconds to go out.

To avoid this always empty the water container each time

you use the dryer (see Maintenance).

●

Door Opening

Opening the door during a programme will stop the dryer

and have the following effects:

Note: The Start/Pause light flashes Amber during the

Heat & Enjoy programme and during the Post Care phase

of a programme.

●

The display shows PAUSED .

●

During a delay phase the delay will continue to count

down. The Start/Pause button must be pressed to

resume the delay programme.

The display will change to show current status.

●

During the drying part of the programme, the colons

on the display stop flashing to show that the time has

stopped counting down.

The Start/Pause button must be pressed to resume

the programme. The display will change to show the

current status, the colons flash and count down

continues.

●

During the Post Care phase, the programme ends.

Pressing the Start/Pause button will restart a new

programme from the beginning.

●

Note

If you have a power cut, switch off the power or remove

the plug. When power is restored, press the Start/Pause

button and the programme will resume.

0:20

0:30

1:00

1:30 2:00

2:00

2:40 3:00

Sound, Delay Timer,

Crease Care, High Heat

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 19 20

Commentaires sur ces manuels

Pas de commentaire

Hotpoint TCUD 93B 6P/Z (UK) Mode d'emploi Page 11

Commentaires sur ces manuels

Produits connexes et manuels pour Séchoirs à tambour Hotpoint TCUD 93B 6P/Z (UK)