Hotpoint CT NTC IW0 Mode d'emploi télécharger pdf (Page 11)

hotpoint.eu

body and directly lling it with water, using a

common bottle or jug.

Place a glass or large container under the

dispense area and touch the dispense button to

operate the unit, and touch again to stop the ap-

pliance.Allowwatertorunthroughtheunituntil

the reservoir has been emptied.

Do not consume the water until step A8

has been completed.

The rst 3-5 litres of water dispensed may

contain some ne, black carbon particles. car-

bon is a natural, organic material made from

coconut shell so don’t worry for your safety.

Clear water should be noticed after ushing

through 3 to 5 litres of water (2 to 3 full re-

servoirs).

Repeatstepsa2-a7vetimes(5x):thiswill

completelyushthecarbonfromthenewlter.

PRODUCT USAGE

When the appliance is in standby mode the

button will be blue but when it is touched it will turn

green and water will be dispensed.

If the button is not touched within 2 mi-

nutes of being activated then it will au-

tomatically stop the ow of water and turn the

pump off.

Touch to STOP dispensing water. When you

touch the button to stop water being dispensed

the button will change colour from green to blue.

After one minute the product is in a

stand-by mode, it goes in an energy sa-

ving mode as the UV lamp is off; when the pro-

duct is in this condition, there will be a 2 se-

cond delay before the water is dispensed after

the dispense button is touched so to activate

the UV lamp and purify the water.

Your product has been designed and in-

ternationally certied to the highest

standards of water purication, and guarante-

es at all times, to dispense the best water qua-

lity. The self monitoring system will warn you

of any potential risks, by way of 3 possible

alarms.

Once the Filter has is at 11 months after its

rstusage,theFiltericonwillashasareminder,

andcontinuetoashuntilthelterhasbeenre-

placed as per B4 below. During this time, your

machinewillcontinuetodispensewater,untilB4

below has been reached.

Aftera12monthperiod,boththeUVBulb

and Filter must be replaced to ensure optimal wa-

terpurication.BoththeUVIconandFilterIcon

will alarm 20 times and ash alternately. When

this occurs, no water will be dispensed, until the

FilterandUVBulbhavebothbeenreplacedand

the machine reset (to do this you will need to fol-

low steps C1 to C17).

MAINTENANCE

This product is a high performance water machi-

ne,keepingitingoodworkingorderwillprovide

thereassuranceoftrulygreatdrinkingwater.

The uv bulb and lter must be replaced

every 12 months to ensure that your ap-

pliance is dispensing the highest quality drin-

king water.

For the correct and effective appliance

working, use only hotpoint-ariston

[hotpoint] replacement kit (read service sec-

tion)

Unplug the Appliance from the mains

before replacing the UV lamp or lter.

It’s recommended to do next steps on a wa-

shable surface. After this procedure it’s re-

commended that you clean the surface with a

home-use disinfecting product.

Remove the water reservoir from the main

body of the appliance.

Remove the two screws that hold the lid in

place using the screwdriver you can nd in the

box.

Remove the lid from the unit by slightly

pushingitbackandthenliftingitup.

Disconnect the UV lamp connector by hol-

ding it and pressing in the clip on the connector

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 60 61

Commentaires sur ces manuels

Pas de commentaire

Hotpoint CT NTC IW0 Mode d'emploi Page 11

Commentaires sur ces manuels

Produits connexes et manuels pour Non Hotpoint CT NTC IW0