Hotpoint OS 1A 300 H 2 Mode d'emploi télécharger pdf (Page 7)

portions; this will also be useful when the frozen items are to

be used.

1. At least 24 hours before storing fresh food in the appliance, press

the fast freeze button.

2. Place the food to be frozen

and keep the lid of the appliance closed for 24 hours. The fast freeze

function automatically deactivates after about 50 hours.

APPLIANCE DEFROSTING

The appliance should be defrosted when the thickness of

ice on the walls reaches 5-6 mm.

• Disconnect the appliance from the power supply.

• Remove food from the appliance and put it in a very cool place

or a thermally insulated bag.

• Leave the appliance door open.

• Remove the internal defrost water drain plug (depending on

model) (Fig. 8).

• Remove the external defrost water drain plug (depending on

model) and reposition it as shown in g. 8).

• Use the separator (depending on model) inside the product as a

recipient for any remaining water, (D) as shown in g. 8. If there is

no separator, use a shallow container.

• Defrosting can be sped up by using a spatula to detach the frost

from the appliance walls.

• Remove the frost from the bottom of the appliance.

• In order to avoid permanent damage to the appliance interior,

do not use pointed or sharp metal instruments to remove the

ice.

• Do not use abrasive products or heat up the interior articially.

• Dry the inside of the appliance thoroughly.

• Ret the plug after defrosting.

CLEANING AND MAINTENANCE

• Remove the frost from the upper edges (see Troubleshooting

Guide).

• Clean the inside after defrosting, using a sponge dampened

with warm water and/or mild detergent.

• Clean the side vent (if provided).

Unplug the appliance before carrying out maintenance

operations. Do not use abrasive products, scourers or stain-

removers (e.g. acetone, trichloroethylene) to clean the

appliance.

To obtain the best results from your appliance, carry out

cleaning and maintenance at least once a year.

HANGING THE LID LIGHT BULB IF PROVIDED

• Disconnect the appliance from the mains power supply.

• Remove the diuser by following the sequence of steps shown

in the gure.

• Unscrew the light bulb and replace it with an identical bulb of

the same wattage and voltage.

• Ret the diuser and plug in the appliance.

TROUBLESHOOTING GUIDE

3. The red LED (if provided) remains alight.

• Is there a power failure?

• Is defrosting in progress?

• Is the appliance lid properly closed?

• Is the appliance positioned near a heat source?

• Is the thermostat setting correct?

• Are the ventilation grille and condenser clean?

4. The appliance is too noisy.

• Is the appliance perfectly horizontal?

• Is the appliance in contact with other furniture or objects that

may cause vibrations?

• Has the packaging been removed from under the

appliance?

Note: Gurgling noises from the refrigerating circuit after the

compressor cuts out are perfectly normal.

5. The green LED (if provided) is o and the appliance is not

working.

• Is there a power failure?

• Is the plug properly inserted in the socket?

• Is the electric cable intact?

6. The green LED (if provided) is o and the appliance is

working.

• The green LED is not working. Contact the After Sales

Service for a replacement.

7. The compressor runs continuously.

• Have hot foods been put in the appliance?

• Has the appliance lid been left open for a long time?

• Is the appliance positioned in a very warm room or near heat

sources?

• Is the thermostat setting correct?

• Has the fast freeze function (depending on model) been pressed

by mistake?

8. Too much ice on the upper edge.

• Are the defrost water drainage plugs correctly ositioned?

• Is the appliance lid properly closed?

• Is the appliance lid seal damaged or deformed? (See chapter

“Installation”)

• Have the 4 protection pieces been removed? (See chapter

“Installation”)

9. Condensation forms on the external walls of the appliance

• It is normal for condensation to form under certain atmospheric

conditions (humidity above 85%) or if the appliance is located in

a damp or poorly ventilated room.

The performance of the appliance is in no way aected.

10. The layer of ice on the internal walls of the appliance is not

uniform.

• This phenomenon is quite normal.

AFTERSALES SERVICE

Before contacting After-Sales Service:

1. See if you can solve the problem yourself.

2. Switch the appliance on again to see if the problem has been

solved. If it has not, disconnect the appliance from the power

supply and wait for about an hour before switching on again.

3. If the problem persists after this course of action, contact After-

Sales Service.

Specify:

• the nature of the fault,

• the model,

• the service number (the number after the word SERVICE on the

rating plate on the rear of the appliance),

• your full address,

• your telephone number and area

code.

1 2 3 4 5 6 7 8

Commentaires sur ces manuels

Pas de commentaire

Hotpoint OS 1A 300 H 2 Mode d'emploi Page 7

Commentaires sur ces manuels

Produits connexes et manuels pour Non Hotpoint OS 1A 300 H 2