Hotpoint PZ 640 T GH NG Mode d'emploi télécharger pdf (Page 5)

200 cm²

Gas connection

This appliance is suitable for use with either a ﬂ exible con-

nection or rigid copper connection. If installing the appliance

with a ﬂ exible connection, the ﬂ exible connection must be

approved to class B or D of AS/NZS1869 as a minimum.

Fit regulator supplied for Natural Gas (if applicable) at rear

of appliance, and as close as practicable to the appliance.

It is recommended that an isolating valve and union be

ﬁ tted, to enable simple disconnection for servicing. These

are to be in an accessible location.

Flexible hose

If a ﬂ exible hose is used, it should be as short as possible

with a maximum length of 1.5 metres;

it should not be bent or kinked;

it should not be in contact with the rear wall of the appli-

ance or in any case with parts which may reach a tem-

perature of 50°C;

it should not come into contact with pointed parts or sharp

corners;

it should be easy to inspect along its entire length in order

to be able to check its condition.

The supply connection point must be accessible with the

appliance installed.



Gas type conversion

If the hob is to be converted for use with a type of gas other

than that for which it was set in the factory (indicated on the

cooktop data plate), the burner injectors must be replaced as

follows:

Remove the pan supports and the burners.

Unscrew the injectors (“A” in ﬁ ugure below) using a 7 mm

socket wrench, and replace them with injectors of suitable

oriﬁ ce diameter, as indicated on the appliance data plate.

Reassemble the parts.



Electrical connection

The electrical supply for the cooktop must be a 240 Volt 50

Hz.

The fuse and electrical wiring of the home/premises must

support the load of the appliance.

The appliance must be earthed. A 3 pin ﬂ exible power cord

is supplied with the appliance to allow the cooktop to be

connected to a properly earthed and rated power socket.

The ﬂ exible cord of the appliance must not be subject to

direct heat and must be positioned after installation of the

appliance so that its temperature does not exceed 75°C.

IMPORTANT If a power socket needs to be installed or

relocated, the work must be done by a licensed electrician.



Installation

If a regulator is required for the new gas type, instal an ap-

proved regulator of appropriate pressure setting and ﬂ ow

capacity.

Replace the gas type label with one suitable for the new

gas type.

Perform the post installation checks as described later in

this manual. In particular, check the turn down setting of

each burner and adjust where necessary.



Fitting the cooktop above an oven

When installing the cooktop above an oven, both the electric-

ity supply cable and the gas pipe or ﬂ exible hose must not

touch hot parts of the oven housing.

When installing above a built-under oven without forced cool-

ing ventilation, suitable air vents should be provided for as

shown in the ﬁ gure (inlet at least 200 cm² from the bottom,

outlet at least 120 cm²

from the top part) to

allow adequate ventila-

tion inside the housing

unit.

Also a wooden panel

“A” should be installed

beneath the hob as in-

sulation, positioning it

at a minimum distance

of 15 mm from the hob

housing

Perform post installation checks and ensure proper and safe operation

before leaving. Test all burners individually and in combination.

1 2 3 4 5 6 7 8

Commentaires sur ces manuels

Pas de commentaire

Hotpoint PZ 640 T GH NG Mode d'emploi Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Non Hotpoint PZ 640 T GH NG