Hotpoint SX 1046L PX S Mode d'emploi télécharger pdf (Page 16)

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

• Theinsideoftheovenshouldideallybecleanedafter

each use, while it is still lukewarm. Use hot water and

detergent, then rinse well and dry with a soft cloth. Do

not use abrasive products.

• Allaccessories-withtheexceptionoftheslidingracks

- can be washed like everyday crockery, and are even

dishwasher safe.

• Werecommendthatdetergentsarenotsprayeddirectly

onto the control panel, but that a sponge is used instead.

! Never use steam cleaners or pressure cleaners on the

appliance.

Cleaning the oven door

! The door of LED INSIDE models cannot be removed.

Clean the glass part of the oven door using a sponge and

a non-abrasive cleaning product, then dry thoroughly with

a soft cloth. Do not use rough abrasive material or sharp

metal scrapers as these could scratch the surface and cause

the glass to crack.

For more thorough cleaning purposes, the oven door may

be removed:

1. Open the oven door fully (see diagram).

2. Use a screwdriver to lift up and turn the small levers F

located on the two hinges (see diagram).

3. Grip the door on the two outer

sides and close it approximately

half way. Pull the door towards you,

lifting it out of its slot (see diagram).

To replace the door, reverse this

sequence.

Inspecting the seals

Check the door seals around the oven regularly. If the seals

are damaged, please contact your nearest Service Centre

(see Assistance). We recommend that the oven is not used

until the seals have been replaced.

Replacing the light bulb

To replace the oven light

bulb:

1. Remove the glass cover

of the lamp-holder.

2. Remove the light bulb and

replace it with a similar one:

halogen lamp voltage 230 V,

wattage 25 W, cap G 9.

3. Replace the glass cover

(see diagram).

Glass cover

Lamp

Holder

compartment

! Do not touch the light bulb directly with your hands.

! Do not use the oven lamp as/for ambient lighting.

Sliding rack kit assembly

To assemble the sliding

racks:

1. Remove the two frames,

lifting them away from the

spacersA(seegure).

2. Choose which shelf to use

with the sliding rack. Paying

attention to the direction in

which the sliding rack is to

beextracted,positionjointB

and then joint C on the

frame.

3. Secure the two frames

with the guide rails using the

holes provided on the oven

walls (see diagram). The

holes for the left frame are

situated at the top, while the

holes for the right frame are

at the bottom.

4. Finally, t the frames on

the spacers A.

! Do not place the sliding racks in position 5.

Automatic cleaning by PYROLYSIS

The cleaning cycle can cause the internal temperature of

the oven to reach 500°C. The pyrolytic cycle is activated,

burning away food and grime residues. Dirt is literally

incinerated.

Keep children away from the appliance during the automatic

cleaning cycle as surfaces may become very hot. Particles

may ignite inside the oven as a result of the combustion

process. There is no cause for concern: this process is both

normal and hazard-free.

Before initiating the PYROLYTIC cycle:

• cleantheovendoor;

• removelargeorcoarsefoodresiduesfromtheinsideof

theovenusingadampsponge.Donotusedetergents;

• removeallaccessoriesandtheslidingrackkit(where

present);

• do not place tea towels or pot holders over the oven

handle.

Left

guide rail

Right guide

rail

Direction

of extraction

* Only available on certain models.

1 2 ... 11 12 13 14 15 16 17 18 19 20

Commentaires sur ces manuels

Pas de commentaire

Hotpoint SX 1046L PX S Mode d'emploi Page 16

Commentaires sur ces manuels

Produits connexes et manuels pour Non Hotpoint SX 1046L PX S