Hotpoint FTVF NW 85C GP (UK) Mode d'emploi télécharger pdf (Page 13)

Start and Programmes

●

Programmes knob

! Warning, if after pressing the START/PAUSE button

the programme knob position has changed, the new

position will NOT change the programme selected.

To change a selected programme, press the

START/PAUSE button , the light flashes Amber to

indicate the programme is paused. Select the new

programme and any options required, the light will then

flash green. Press the START/PAUSE button again

and the new programme will start.

●

OPTION buttons / lights

These buttons are used to customise the selected

programme to your requirements. A programme must

have been selected on the programme knob before an

option can be selected. Not all options are available for all

programmes (see Start and Programmes). If an option is

not available and you press the button, the buzzer will

beep three times. If the option is available the option light

in the button lights to confirm the selection.

After the START/PAUSE button has been pressed only the

Crease Care option (where available) can be changed.

Progress ( Drying, Cool Tumble) icons

These are part of the Display, they indicate the progress

of the dryer. Each icon comes on as the corresponding

phase starts.

Delay (Time Delay)

The start of some programmes (see Start and

Programmes and The Display) can be delayed for up to

24 hours.

Crease Care

The pre-care option is only available if a delayed start has

been selected. It tumbles the clothes occasionally during

the delayed period to help prevent creases developing.

The post-care option occasionally tumbles the clothes

after the end of the drying and cool tumble cycles to prevent

creases developing, should you not be available to

remove the load immediately the programme is complete.

The display will show ‘End’.

Note: The Crease Care and the Start/Pause lights flash

Amber during this phase.

Selecting this option enables both the pre and post care

functions if appropriate and when selected the light in the

button is lit.

Extra Care

This Anti-Ageing function for Cottons helps to maintain

the brightness of your laundry for a long time, thanks to

the correct drum rotation (reduced in the last part of the

cycle) and the correct temperature.

Note: It cannot be used with the ‘Extra Dry’ and

‘Cupboard Dry’ dryness levels.

The Controls

8:88

Fibre Care button and lights

Allow the choice of heat levels to suit different textiles.

Not all programmes allow you to change the heat level

and some programmes allow all three heat level options:

Low, Medium and High.

When the heat level options are available pressing this

button changes the heat level and the light corresponding

to the selection is lit.

●

DISPLAY

The display shows either the amount of time delay

remaining or an indication of the amount of time left for a

drying programme (see The Display).

The colons between the hours and minutes in the display

flash to show that the time is counting down.

When the programme finishes its cool tumble phase the

display will show ‘End’.

●

Door Opening

Opening the door (or pressing the Start/Pause button)

during a programme will stop the dryer and have the

following effects:

Note: The Start/Pause light flashes Amber during the Post

Care phase of a programme.

●

The START/PAUSE light flashes Amber.

●

The START/PAUSE button must be pressed to

resume the programme, including a delayed

start. The progress lights will change to show the

current status and the START/PAUSE light will stop

flashing and turn green.

●

During a delay phase the delay will continue to

count down.

●

During the drying part of a programme, the time to

end count continues but the colons do not flash.

●

During the post-care phase of a drying programme,

the programme will finish. Pressing the

START/PAUSE button will re-start a new programme

at the beginning.

●

Changing the programmes knob will select a new

programme and the START/PAUSE light will flash

green. You can use this to select the Refresh

programme to cool the clothes, if you find them

dry enough. Press the START/PAUSE button to

begin a new programme.

●

Note

If you have a power cut, switch off the power or remove

the plug. When power is restored, press and hold the

ON/OFF button until the dryer reactivates, then press the

Start/Pause button.

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 19 20

Commentaires sur ces manuels

Pas de commentaire

Hotpoint FTVF NW 85C GP (UK) Mode d'emploi Page 13

Commentaires sur ces manuels

Produits connexes et manuels pour Machines à laver Hotpoint FTVF NW 85C GP (UK)