Hotpoint FDFAO 32121 X Mode d'emploi télécharger pdf (Page 5)

* Only available in selected models.

Electrical connection

Before inserting the plug into the electrical socket, make

sure that:

• The socket is earthed and complies with current

regulations;

• the socket can withstand the maximum load of the

appliance as shown on the data plate located on the inside

of the door

(see chapter Description of the appliance);

• The power supply voltage falls within the values indicated

on the data plate on the inside of the door.

• The socket is compatible with the plug of the appliance.

If this is not the case, ask an authorised technician to

replace the plug (

See Repairs and After Sales

). Do not

use extension cables or multiple sockets.

Once the appliance has been installed, the power supply

cable and the electrical socket should be easily accessible.

The cable should not be bent or compressed.

If the power supply cable is damaged, have it replaced

by the manufacturer or its authorised Technical Assistance

Service in order to prevent all potential hazards.

(See Repairs

and After Sales)

The Company shall not be held responsible for any

incidents, if these regulations are not observed.

This appliance must be earthed.

Fuses:your appliance comes fitted with a plug and a 13A fuse. If

you need to replace the fuse, only those rated at 13A and ASTA

approved to BS1362 should be used. If you lose the fuse cover, a

replacement may be obtained from your local authorised Service

Centre or Electrical company. Correct replacement is identified

by colour coding or the marking on base of plug.

DO NOT use the plug unless the fuse cover is fitted.

Changing the Plug

Cut off and dispose of the supplied plug if it does not fit your

socket.

To avoid a shock hazard DO NOT insert the discarded plug

into a socket anywhere else.

Wires in the mains lead are coloured accordance with the

following code:

Green/Yellow - Earth

Blue - Neutral

Brown - Live

If you change the plug, the colour of the wires in the mains lead

may not correspond with the terminal markings in the plug, which

if not coloured, could be:

EARTH ‘E’ or

NEUTRAL ‘N’

LIVE ‘L’

Advice regarding the first wash cycle

After the installation, remove the stoppers from the racks and

the retaining elastic elements from the upper rack

(if any).

Water softener settings

Before starting the first wash cycle, set the hardness lev-

el of the water from the mains supply.

(see chapter Rinse aid

and refined salt).

First load the softener tank with water, then introduce about

1 kg of salt. It is perfectly normal for water to flow out.

As soon as this procedure is complete, run a wash cycle.

Only use salt that has been specifically designed for dish-

washers.

After the salt has been poured into the machine, the LOW

SALT indicator light* switches off.

If the salt container is not filled, the water softener and the

heating element may be damaged as a result.

Changing the Mains Lead

A lead can be ordered from Hotpoint Service:

- If you have damaged the existing lead or require a longer one

a charge will be made. It is strongly advised that this work is

carried out by a qualified electrician.

- If the domestic wiring includes a residual current-operated

circuit breaker, ensure that it conforms to the latest regulations.

The dishwasher must not be connected to the electricity supply

while installation is being carried out.

- This appliance should only be connected to a 230/240V AC

source, via a properly installed earthed socket.

- Use the dishwasher solely in a domestic environment.

- DO NOT stand or place heavy objects on the door when it is

open, this could damage the door or cause the appliance to tip

forward.

1 2 3 4 5 6 7 8 9 10 ... 15 16

Commentaires sur ces manuels

Pas de commentaire

Hotpoint FDFAO 32121 X Mode d'emploi Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Lave-vaisselle Hotpoint FDFAO 32121 X