Hotpoint RI 861 X Mode d'emploi télécharger pdf (Page 3)

INSTALLATION

Recommendations

Important: Disconnect the hob from the mains before carrying out any

installation work or servicing.

• All electrical connections must be made before connecting the appliance to

the power supply.

• Installation must be carried out by a qualied technician in accordance with the

manufacturer’s instructions and in compliance with local regulations.

• Unpack the hob and make sure that the appliance has not been damaged during

transport. If you are not sure contact the dealer or the nearest service centre.

Preparing the housing unit

• Cut the worktop to t before installing the appliance. Carefully remove any

shavings or sawdust that could prevent the appliance from running properly.

Attention: to install the hob on other surfaces than wood (marble, plastic, ceramic,

marble, stone, etc.) remember to ask After Sales Service for the xing plates (g.

2) Code 4819 404 78697.

• The hob must be tted in a worktop with a minimum thickness of 20 mm and

a maximum of 50 mm.

• Insert a separator panel at a minimum distance of 90 mm from the bottom of

the hob, so that it cannot be accessed by the user.

• If there is an oven under the hob, make sure that it is manufactured by us and

equipped with a cooling system.

• There must be nothing between the hob and the oven (e.g. cables, insulating

material, etc.).

• An adjacent column unit must be installed at least 100 mm from the edge of

the hob.

• Cut an opening in the worktop of the given dimensions.

• We recommend you seal the internal edges of the worktop with wood glue or

silicone.

• If not already in place, apply the supplied seal to the hob, after cleaning the

adhesive surface thoroughly.

Glass-ceramic hob

Important: remove any protective lm before installing the hob.

Make sure that that the opening in the worktop for the hob is cut according to the

dimensions given in the drawing, paying attention to the tolerance range.

The hob should not be forced into the worktop. Forcing the glass-ceramic top may

cause it to crack (even at a later date)!

• If the worktop is made of wood, use the spring clips and screws provided.

1. Secure the spring clips (A) (g. 1) with the screws provided (B) (g. 1) as shown,

paying attention to the specied distances.

2. Fit the hob into the worktop.

• If the worktop is made of marble, plastic, ceramic, stone, etc., the hob must be

secured with special brackets (C) (g. 2).

1. Fit the hob into the worktop (g. 1).

2. Place the 4 brackets (C) in position in accordance with the thickness of the

worktop as shown in g. 2.

3. Fasten the 4 screws (D) in the positions (E) (g. 2).

Electrical connection

• Regulations require that the appliance be earthed.

• Connection to the mains must be carried out by a qualied technician in

accordance with the manufacturer’s instructions and in compliance with local

regulations.

• The installer is responsible for connecting appliances correctly to the mains and

for observing the safety regulations.

• The oven power cable must be long enough to connect the built-in appliance

to the mains.

• Observance of safety directives requires that a multipole switch with a minimum

contact gap of 3 mm be used for the installation.

• Do not use multiple plug adapters or extension leads.

• After the oven has been installed, the electrical components must be

inaccessible.

Connecting the oven to the power supply

Note: the yellow/green earth wire must be connected to the screw with the symbol

• Strip approx. 70 mm of the cable sheath from the power supply cable (G).

• Strip approx. 10 mm of sheath from the conductors. Insert the cable (G) through

the opening in the lid (F).

• Insert the cable into the cable clamp and connect the conductors to the terminal

block as indicated in the diagram printed on the lid.

• Secure the power cable (G) by means of the cable clamp.

• Ret the protection lid (F).

• After the electrical connection, t the hob from the top and hook it to the xing

springs, according to the illustration.

Declaration of conformity

• This cooktop is suitable for contact with foodstuffs and complies with EEC (CE)

Regulation n. 1935/2004.

• This hob (Class Y) has been designed to be used only for cooking. Any other

use (such as heating a room) is improper and dangerous.

• This hob has been designed, constructed and marketed in compliance with:

- safety objectives of the “Low Voltage” Directive 2006/95/EC (which replaces

73/23/EEC and subsequent amendments);

- the protection requirements of Directive “EMC” 2004/108/EC;

- requirements of EEC Directive 93/68.

The Manufacturer reserves the right to change product specications without

prior notice.

1 2 3 4

Commentaires sur ces manuels

Pas de commentaire

Hotpoint RI 861 X Mode d'emploi Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Plaques chauffantes Hotpoint RI 861 X