Hotpoint SMO654OFBTIXL Guide d'utilisation et d'entretien télécharger pdf (Page 6)

Use & Care guide

FIRST TIME USE

DAILY USE

HOW TO USE THE APPLIANCE

ACCESSORIES

POTS AND PANS

Only use pots and pans made from ferromagnetic

material which are suitable for use with induction hobs.

To determine whether a pot is suitable, check for the

symbol (usually stamped on the bottom). A magnet

may be used to check whether pots are magnetic.

The quality and the structure of the pot base can alter cooking performance.

Some indications for the diameter of the base do not correspond to the

actual diameter of the ferromagnetic surface.

EMPTY POTS OR POTS WITH A THIN BASE

Do not use empty pots or pans when the hob is on.

The hob is equipped with an internal safety system that constantly

monitors the temperature, activating the “automatic o” function where

NOOK

high temperatures are detected. When used with empty pots or pots with

thin bases, the temperature may rise very quickly, and the “automatic o”

function may be triggered with a slight delay, damaging the pot or pan. If this

occurs, do not touch anything, and wait for all components to cool down.

If any error messages appear, call the service centre.

MINIMUM DIAMETER OF POT/PAN BASE FOR THE DIFFERENT

COOKING AREAS

centered on

1 point

10 cm

19 cm

sh kettle/

grill pan

sh kettle/

grill pan

2 points

covered

3 points

covered

4 horizontal

points

covered

OFF

Max

MinMed

OFF

Max

MinMed

OFF

Max

MinMed

OFF

Max

Min Med

POWER CONTROL

With the “Power control” function, you can set the maximum power

level for the hob, based on your needs or on the capacity of your mains

power supply.

Once the maximum power has been set, the hob automatically adjusts

the charge distribution to the dierent cooking zones and an acoustic

signal will sound when the limit is reached.

This setting can be used at any time and will remain until it is changed.

At the time of purchase, the hob is set to the maximum possible power

(nL). The maximum power level (nL) is printed on the identication plate

on the bottom of the hob.

To set the hob power:

Once the appliance is connected to the mains power, the power level

can be set within 60 seconds.

• Press and hold down the

control for 3seconds. The display will

read

• Hold down the control until the last power setting is shown.

• Use the

and controls to select the required power.

Available power settings are: 2.5kW – 4.0kW – 6.0kW – 7.4kW.

• Press to conrm.

The selected power will remain in the memory, even in the case of a

power outage.

To vary power levels, disconnect the appliance from the mains power

for at least 60seconds, then reconnect it and repeat the steps above.

In case of error during the setting sequence, the display will show the

symbol and an acoustic signal will be sounded. In this case, you will

need to repeat the operation.

If the error persists, contact the assistance service.

ACOUSTIC SIGNAL ON / OFF

To switch the acoustic signal on/o:

• Switch on the cook top.

• Hold down the

control on the rst slider to the left, for 3seconds.

Any alarms set will remain active.

3”

OFF

Max

MinMed

OFF

Max

Min Med

OFF

Max

MinMed

OFF

Max

MinMed

SWITCHING THE HOB ON/OFF

To turn the hob on, press the power button for around 1 second, until

the cooking zone display lights up.

To turn the hob o, press the same button again, and all cooking zones

will be deactivated. If no function is selected, the hob will automatically

switch o after 10 seconds.

If the hob is being used, switching it o will switch o all cooking zones,

and the residual heat indicator, “H”, will remain lit until all of the cooking

zones have cooled.

POSITIONING

1. Locate the desired cooking zone, by referring to the position

symbols at the bottom of each slide touchscreen.

2. Place the pan in the chosen area, making sure that it covers one or

more of the reference marks on the surface of the hob.

3. Do not cover the control panel symbols with the cooking pot.

Please note: In the cooking zones close to the control panel, it is advisable to

keep pots and pans inside the markings (taking both the bottom of the pan

and the upper edge into consideration, as this tends to be larger).

This prevents excessive overheating of the touchpad. When grilling or frying,

please use the rear cooking zones wherever possible.

ACTIVATING/DEACTIVATING COOKING ZONES AND ADJUSTING

POWER LEVELS

OFF

To switch on a cooking zone:

1. Switch on the hob.

2. Set the required power level by sliding your nger across the slider

control (SLIDER) for the cooking zone of choice.

The power level will appear above the slider. Each cooking zone has

dierent power levels, ranging from “1” (minimum) to “18” (maximum).

Using the slider controls it is also possible to select the quick heat

function, which is marked “P” on the display.

1 2 3 4 5 6 7 8 9 10 11 ... 14 15

Commentaires sur ces manuels

Pas de commentaire

Hotpoint SMO654OFBTIXL Guide d'utilisation et d'entretien Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Plaques chauffantes Hotpoint SMO654OFBTIXL