Hotpoint AQCF 852 B I (UK) Mode d'emploi télécharger pdf (Page 12)

The Controls

 Programme knob

 Warning, if after pressing the start button the programme

knob position is changed, the new position will NOT change

the programme selected.

To change programme press Start/Pause Button

to pause

the programme, the light flashes Amber, select new

programme and any option, the light will then flash green. Press

the Start/Pause Button

and the new programme will start.

 Option Buttons/ Lights

These buttons are used to customise the selected

programme to your requirements. Not all options are

available for all programmes (see Start and Programmes).

If an option is not available and you press the button, the

buzzer will beep three times. If the option is available there

will be one beep and the option light next to the button

lights to confirm the selection.

 ECO Light

This light is illuminated when you select programme

options that will use less energy than the default setting.

Examples are if you choose an Automatic or sensing

programme or use a timed dry setting less than the default

time. This light does not indicate that the optimum setting

for energy use has been selected; it only shows you that

your selected options will use less energy.

 Progress (

Drying, Cool tumble, ) Lights

The Progress lights show you the status of the programme. At

each stage of the programme the corresponding light turns on.

 Delay Start

The start of some programmes (see Start and Programmes)

can be delayed for up to 24 hours (see The Display).

Ensure the water bottle is emptied and the filter is cleaned

before setting a delayed start.

 Pre Care

When a delayed start and this option have been selected

the clothes are tumbled occasionally during the delayed

period to help prevent creases developing.

 Post Care

When selected, the clothes are occasionally tumbled after

end of the drying and cool tumble cycles to help prevent

creases developing, should you not be available to remove

the load immediately after the programme is complete. The

light is on during this phase.

Mini Load

Available with. Cotton High Heat, Cotton Low Heat, Shirts

High Heat, Shirts Low Heat and Synthetic Programmes.

Used for loads between 1 and 2 kg.

This programme optimises Sensor Dry automatic

programmes for smaller loads and improves the time to

end estimation.

 Empty Water Clean Filter Light

H2O

(If you have plumbed your dryer to a drain the light can

be ignored for the water bottle, as there is no need to

empty the water container). When

is on (not flashing) it

reminds you to empty the water container. If the water

container fills during a programme, the heater turns off and

the dryer does a period of Cool Tumble then the light

flashes and the buzzer sounds. You must empty the

container and restart the dryer or the clothes will not dry.

After re-starting the dryer the light will take a few seconds

to go out. To avoid this always empty the water container

each time you use the dryer (see Maintenance).

Please note that you ALWAYS have to clean the filter even

if you have plumbed your dryer to a drain.

 Door Opening

Opening the door (or pressing the Start/Pause Button)

during a programme will stop the dryer and have the

following effects.

 The Start/Pause Light flashes Amber.

 During a delay phase the delay will continue

to count down. The start button must be

pressed to resume the delay programme. One

of the delay lights will flash to show the current

delay setting.

 The start button must be pressed to resume the

programme. The progress lights will change to

show the current status and the Start/Pause

light will stop flashing and turn green.

 During the post creasecare phase of a drying

program, the Programme will finish. Pressing the

Start/Pause button will restart a new program

at the beginning.

 Changing the Programmes knob will select a

new programme and the Start/Pause Light will

flash green. You can use this to select the Cool

Tumble programme

to cool the clothes if you

find them dry enough.

Pressing the start/pause button to begin new

Programme.

 Note

If you have a power cut, switch off the power or remove

the plug, press the start button and the programme will

resume.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Commentaires sur ces manuels

Pas de commentaire

Hotpoint AQCF 852 B I (UK) Mode d'emploi Page 12

Commentaires sur ces manuels

Produits connexes et manuels pour Séchoirs à tambour Hotpoint AQCF 852 B I (UK)