Hotpoint FTCF 87B 6HY1 EU Mode d'emploi télécharger pdf (Page 13)

The Controls

! Warning, after pressing the START/PAUSE button ,

the programme cannot be changed. To change a selected

programme, press the START/PAUSE button

the light

flashes Amber to indicate the programme is paused. Select

the new programme and any options required, the light will

then flash green. Press the START/PAUSE button

again

and the new programme will start.

• Option buttons

These buttons serves to personalise the selected

programme according to personal requirements.

Not all options are available for all programmes.

Some options are incompatible with the ones

previously set. If the button of any unavailable option

is pressed, the buzzer will beep 3 times. If the option

is available, the option light will stay on.

Progress ( Drying, Cool Tumble) icons

These are part of the Display, they indicate the progress of

the dryer. Each icon comes on as the corresponding phase

starts.

Delay Timer (Time Delay)

The start of some programmes (see The Display and

Programmes tables) can be delayed for up to 24 hours.

Ensure the water container is emptied before setting a

delayed start.

Ready to Iron

This option allows you to dry loads where only some of the

items need ironing and you do not wish to fully dry those

items. When Iron Dry level is reached, a buzzer sounds

to let you know that the items that need ironing can be

removed. The dryer then stops and the START/PAUSE

light flashes orange. Remove the items you wish to iron,

close the door and press the START/PAUSE button

, the

dryer continues until the remaining items reach the selected

dryness level. It can be used for load sizes up to 3kg.

Less Tangled

This option has the drum movement modified to give a

tumbling action that reduces tangling and knotting of your

clothes. The Less Tangled option gives best results when

used with smaller loads.

Heat Level button and lights

Not all programmes allow you to change the heat level and

some programmes allow all three heat level options:

Low, Medium and High.

When the heat level options are available pressing this

button changes the heat level and the light corresponding to

the selection is lit.

• DISPLAY “8:88”

The display shows either the amount of time delay remaining

or an indication of the amount of time left for a drying

programme (see The Display). The colons between the

hours and minutes in the display flash to show that the time

is counting down. When the programme finishes its cool

tumble phase the display will show ‘End’.

• Empty Water Icon / Container

(If you have plumbed your dryer to a drain this icon can be

ignored, as there is no need to empty the water container).

When this icon is on (

) it reminds you to empty the water

container.

If the water container fills during a programme, the heater turns

off and the dryer does a period of Cool Tumble then the buzzer

sounds, the ‘water container full’ icon

flashes, the display

shows “H20” and the ‘empty water’ icon

is on.

You must empty the water container and restart the dryer or

the clothes will not dry. After re-starting the dryer the display will

take a few seconds to refresh. To avoid this always empty the

water container each time you use the dryer (see Maintenance).

• Door Opening

Opening the door (or pressing the Start/Pause Button) during a

programme will stop the dryer and have the following effects:

• The START/PAUSE light flashes Amber.

• During a delay phase the delay will continue to count

down. The START/PAUSE button must be pressed to

resume the delay programme.

• The START/PAUSE button must be pressed to resume

the programme. The progress lights will change to show

the current status and the Start/Pause light will stop

flashing and turn green.

• Changing the Programmes knob will select a new

programme and the START/PAUSE Light will flash

green. You can use this to select the “Refresh”

programme to cool the clothes if you find them dry

enough. Pressing the START/PAUSE button to begin

new Programme.

• Note

If you have a power cut, switch off the power or remove the

plug. When power is restored, plug in the machine, press and

hold the ON/OFF button until the dryer reactivates, then press

Start/Pause button.

Start and Programmes

1 2 ... 8 9 10 11 12 13 14 15 16

Commentaires sur ces manuels

Pas de commentaire

Hotpoint FTCF 87B 6HY1 EU Mode d'emploi Page 13

Commentaires sur ces manuels

Produits connexes et manuels pour Séchoirs à tambour Hotpoint FTCF 87B 6HY1 EU