Hotpoint WT640 Manuel d'utilisateur télécharger pdf (Page 19)

Something Wrong?

Troubleshooting

 The transit fixings were not removed correctly (see Installation Remove the transit fixings )

- Failure to remove all the parts of the transit fixings will cause the machine to vibrate

excessively during spin.

Note: There are TWO transit fixings that need to be removed - two bolts, two washers,

two rubber grommets and two nylon spacers.

 The machine is not level (see Installation )-Adjust the feet so that the machine stands firm on the

floor (ie,it does not rock) and ensure the machine is level from front to back and from side to side.

 The machine is closed in, between furniture cabinets and the wall (see Installation ).

 Perhaps the machine was attempting to spin an unbalanced load -Try the machine again

with a different wash load.

 When you sort your laundry into wash groups, check all loose items, such as coins are

removed from the laundry. Check the drum at the end of each cycle and remove any loose

items (coins etc).

Note: Super Silent refers to wash sound level only -there will always be some motor

and drum noise during spin.

...from behind or underneath:

 Check each end of the cold water inlet hose, ensuring connections at both ends are tight

and not leaking (see Installation ).

 Depending on the installation method used (see Installation ). Check that:

- the drain hose is firmly secured to the undersink U trap, or...

- the drain hose is positioned correctly into the standpipe.

 Check that your water pressure is within limits (see Technical Details Chart ).

- If too high, try turning the cold water supply tap down slightly and try the machine

again (see Installation ).

...from the dispenser drawer (water leaking down the front of the machine):

 Check that the detergent dispenser is not blocked or obstructed.

- Remove the drawer from the machine and clean it (see Care and Maintenance ).

 Check the cold water supply tap is turned on sufficiently (see Installation ).

Is your water pressure is within limits (see Technical Details Chart ), if it is too low it may

not be sufficient to flush all the detergent out of the drawer.

 Check that the detergent dispenser is not blocked or obstructed.

-Remove the drawer from the machine and clean it (see Care and Maintenance ).

 Is your water pressure too low? (see T echnical Details Chart ).

Note:Are you using detergent tablets? - If yes, please check the detergent

manufacturers instructions on the side of the detergent box, not all detergent tablets

are suitable for use in the dispenser drawer some need to be placed into the machine

drum with the wash load for them to dissolve correctly.

 Check that the detergent dispenser is not blocked or obstructed.

-Remove the drawer from the machine and clean it (see Care and Maintenance ).

The machine makes a

noise or vibrates too

much during the spin

cycle.

The machine leaks:

Not all the detergent

has been flushed out of

the dispenser drawer.

The dispenser drawer

will not close properly or

is collecting water.

Section 2: Specific Error Messages on the Control Panel and Digital Display

Your machine carries out automatic checks at various stages of the wash cycles - Error messages will be displayed on the

control panel to indicate there is something wrong.

The error message displayed is dependent upon which machine you have:

Error message:

H2O flashing in the display.

Display shows door.

This indicates that the machine has failed to take in water (see Installation ).

Check that:

 the cold water inlet hose is connected to the cold water supply tap.

 the cold water inlet hose is not kinked.

 the cold water supply tap is turned on - Ensure it is turned fully on.

 the water pressure is sufficient (see Technical Details Chart ).

This indicates that the door is not closed properly.

 Close the door firmly and try the machine again.

This indicates that the machine failed to drain, possibly because the pump filter is blocked.

 Your machine is fitted with a filter system for the pump - This filter may have become blocked.

( see Care and maintenance) for details of how to remove any blockage from the pump filter.

Wash Enhance and Rinse

Hold and Mini Load option

indicator lights flashing on

the control panel.

1 2 ... 14 15 16 17 18 19 20

Commentaires sur ces manuels

Pas de commentaire

Hotpoint WT640 Manuel d'utilisateur Page 19

Commentaires sur ces manuels

Produits connexes et manuels pour Rondelles Hotpoint WT640