Hotpoint HSB 7M124 B EU Mode d'emploi télécharger pdf (Page 9)

Refined Salt and Rinse Aid

Only use products which have been specifically designed

for dishwashers. Do not use table salt or industrial salt.

Follow the instructions given on the packaging.

If you are using a multi-function product, we recommend

that you add salt in any case, especially if the water is hard

or very hard.

(Follow the instructions given on the packaging.)

If you do not add salt or rinse aid, the LOW SALT* and

LOW RINSE AID

* indicator lights will remain lit.

Measuring out the refined salt

The use of salt prevents the formation of LIMESCALE on the

dishes and on the machine's functional components.

• It is important that the salt dispenser be never empty.

• It is important to set the water hardness.

The salt dispenser is located in the lower part of the dishwasher

(see Description)

and should be filled:

• When the LOW RINSE AID indicator light in the control panel

is lit *;

• When the green float* on the cap of the salt dispenser is no

longer visible.

• See autonomy in the water hardness table.

1. Remove the lower rack and unscrew the

container cap (anticlockwise).

2. Only the first time you do this: fill the water

dispenser up to the edge.

3. Position the funnel

(see figure)

and

fill the salt container right up to its edge

(approximately 1 kg); it is not unusual for a

little water to leak out.

4. Remove the funnel and wipe any salt residue away from the

opening; rinse the cap under running water and then screw it on.

It is advisable to perform this procedure every time you add salt

to the container.

Make sure the cap is screwed on tightly, so that no detergent can

get into the container during the wash cycle (this could damage

the water softener beyond repair).

Whenever you need to add salt, we recommend carrying out

the procedure before the washing cycle is started.

Setting the water hardness

For perfect water softener operation, it is essential that the

adjustment be based on the water hardness in your house. Ask

your local water supplier for this information. The factory setting

is for medium water hardness.

• Switch the dishwasher on using the On/Off button.

• Switch it off using the On/Off button

• Press and hold the START/PAUSE button for 5 seconds.

• Switch it on using the On/Off button

• The salt indicator light flashes (as many times as the current

selection.)

• Set the knob to the desired hardness level number

(see Table

on water hardness.)

• Switch it off using the On/Off button

• Setting is complete!

(°dH = hardness measured in German degrees - °f = hardness

measured in French degrees – mmol/l = millimoles per litre)

Measuring out the rinse aid

Rinse aid makes dish DRYING easier. The rinse aid dispenser

should be filled:

• When the LOW RINSE AID indicator light on the panel/display

is lit *;

• When the dark optical indicator* on the dispenser door “D”

becomes transparent.

1. Open the dispenser “D” by pressing and pulling up the tab

on the lid;

2. Carefully introduce the rinse aid as far as the maximum

reference notch in the filling space - avoid spilling it. If this

happens, clean the spill immediately with a dry cloth.

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the tub.

Adjusting the amount of rinse aid

If you are not completely satisfied with the drying results, you

may want to adjust the quantity of rinse aid used.

• Switch the dishwasher on using the On/Off button.

• Switch it off using the On/Off button

• Press the START/PAUSE button three times

• Switch it on using the On/Off button

• The rinse-aid indicator light will flash as many times as the

level that was set.

• Set the knob to the level number of rinse aid quantity to be

supplied.

• Switch it off using the On/Off button

• Setting is complete!

If the rinse aid level is set to ZERO, the rinse aid will not be

supplied and the low rinse aid indicator light will not be lit if you

run out of it.

A maximum of 4 levels can be set according to the dishwasher

model. The factory setting is for a medium level.

• If you see bluish streaks on the dishes, set a low number (1-2).

• If there are drops of water or limescale marks on the dishes,

set a high number (3-4).

Water Hardness Table

Average autonomy

salt dispenser with 1

wash cycle per day

level °dH °fH mmol/l months

1 0 - 6 0 - 10 0 - 1 7 months

2 6 - 11 11 - 20 1.1 - 2 5 months

3 12 - 17 21 - 30 2.1 - 3 3 months

4 17 - 34 31 - 60 3.1 - 6 2 months

34 - 50 61 - 90 6.1 - 9 2/3 weeks

For values between 0°f and 10°f, we do not recommend the use

of salt. A setting of 5 may increase cycle duration.

* Only available in selected models.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 27 28

Commentaires sur ces manuels

Pas de commentaire

Hotpoint HSB 7M124 B EU Mode d'emploi Page 9

Commentaires sur ces manuels

Produits connexes et manuels pour Lave-vaisselle Hotpoint HSB 7M124 B EU