Hotpoint EG600P (T) Mode d'emploi télécharger pdf (Page 3)

Instructions for installation

The following instructions should be read by a qualified

technician to ensure that the appliance is installed, regu-

lated and technically serviced correctly in compliance with

current regulations.

Important: remember to unplug the appliance from the

mains before regulating the appliance or carrying out

any maintenance work.

Positioning

Important: this appliance may be installed and used only

in permanently ventilated rooms in compliance with cur-

rent Norms in force. The following requirements must be

observed.

a) The room must be equipped with an exhaust system

that vents the combustion fumes to the outside. It may

consist of a hood or an electric fan that automatically

starts each time the appliance is turned on.

The room must also have a system to permit proper air circula-

tion, needed for combustion to occur normally. The flow of air

needed for combustion must not be less than 3 m

/h per kW of

installed power. The air circulation system may take air directly

from the outside by means of a pipe with an inner cross section of

at least 100 cm

; the opening must not be able to be accidentally

blocked. For those appliances not equipped with a safety device

for accidental flame loss, the ventilation apertures must be in-

creased by 100%, with the minimum being 200cm

(Fig. A). The

system can also provide the air needed for combustion by indi-

rect means, i.e. from adjacent rooms fitted with air circulation

tubes as described above. However, these rooms must not be

common rooms or bedrooms.

c) Intensive and prolonged use of the appliance may re-

sult in the need for supplemental air circulation, e.g.

opening windows or increasing mechanical venting (if

present).

d) Liquid petroleum gas descends towards the floor as it

is heavier than air. Thus, rooms containing LPG cylin-

ders must also be equipped with apertures to the out-

side for ventilation of gas in the event of leaks. LPG

cylinders must not, therefore, be installed or stored in

rooms or storage areas that are below ground level (cel-

lars, etc.) whether they are partially or completely full.

It is a good idea to keep only the cylinder being used in

the room, positioned so that it is not subject to heat

produced by external sources (ovens, fireplaces, stoves,

etc. ) which could raise the temperature of the cylinder

to above 50°C.

Prior to installing the cooker, 95 ÷ 155 mm high support-

ing feet (provided) should be fitted into the holes to be

found in the bottom of the cooker (fig.F). These feet are

screw-adjustable and whenever necessary should be used

to make sure the cooker stands level.

Installation of the cooker

The appliance can be installed next to furniture units which

are no taller than the top of the cooker hob. The wall in

direct contact with the back panel of the cooker must be

made of non-flammable materials. During operation the

back panel of the cooker could reach a temperature of

50°C above room temperature. For proper installation of

the cooker, the following precautions must be taken:

For trouble-free operation of appliances installed in hous-

ing units, the minimum distances shown in fig.E should

be observed. Adjacent surfaces and the wall at the rear

should also be able to withstand an overheating tempera-

ture of 65°C

a) The appliance can be placed in a kitchen, dining room

or bedsit, but not in a bathroom.

b) Any hoods must be installed according to the require-

ments in the installation manual for the hoods them-

selves.

c) If the cooker is installed beneath a wall cabinet, the

latter must be situated at a minimum of 420 mm above

the hob. The minimum distance between the worktop

and kitchen units made of combustible material is 700

mm (Fig. C and D).

d) The wall in direct contact with the back panel of the

cooker must be made of non-flammable materials.

fig.F

fig.E

95÷155mm

min. 100mm

In a chimney stack or branched flue

(exclusively for cooking appliances)

Directly to the outside

Detail A Room

adjacent

Room to be

ventilated

Examples of ventilation holes

for comburant air

Fig. A

Enlarging the ventilation slot

between

window and floor

Fig. B

1 2 3 4 5 6 7 8 ... 19 20

Commentaires sur ces manuels

Pas de commentaire

Hotpoint EG600P (T) Mode d'emploi Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Fours Hotpoint EG600P (T)