Hotpoint SMO 658 C/BT/IXL/N Guide d'utilisation et d'entretien Page 6

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 14
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 5
6
Use & Care guide
FIRST TIME USE
DAILY USE
HOW TO USE THE APPLIANCE
ACCESSORIES
POTS AND PANS
Only use pots and pans made from ferromagnetic
material which are suitable for use with induction
hobs. To determine whether a pot is suitable,
check for the
symbol (usually stamped on the
bottom). A magnet may be used to check whether
pots are magnetic. The quality of the pots and pans used may aect
performance and cooking results.
EMPTY POTS OR POTS WITH A THIN BASE
Do not use empty pots or pans when the hob is on.
The hob is equipped with an internal safety system that constantly
monitors the temperature, activating the “automatic o” function
where high temperatures are detected. When used with empty pots
or pots with thin bases, the temperature may rise very quickly, and the
NOOK
“automatic o” function may be triggered with a slight delay, damaging
the pot or pan. If this occurs, do not touch anything, and wait for all
components to cool down.
If any error messages appear, call the service centre.
MINIMUM DIAMETER OF POT/PAN BASE FOR THE DIFFERENT
COOKING AREAS
centered
on 1 point
10 cm 19 cm
sh kettle/
grill pan
sh kettle/
grill pan
24 cm
2 points
covered
3 points
covered
4 horizontal
points
covered
4 vertical
points
covered
OFF
P
Max
18
Min Med
OFF
P
Max
18
MinMed
OFF
P
Max
18
Min Med
OFF
P
Max
18
Min Med
POWER CONTROL
With the “Power control” function, you can set the maximum power
level for the hob, based on your needs or on the capacity of your mains
power supply.
Once the maximum power has been set, the hob automatically adjusts
the charge distribution to the dierent cooking zones and an acoustic
signal will sound when the limit is reached.
This setting can be used at any time and will remain until it is changed.
At the time of purchase, the hob is set to the maximum possible power
(nL). The maximum power level (nL) is printed on the identication plate
on the bottom of the hob.
To set the hob power:
Once the appliance is connected to the mains power, the power level
can be set within 60 seconds.
Press and hold down the
control for 3seconds. The display will
read
.
Hold down the control until the last power setting is shown.
Use the
and controls to select the required power.
Available power settings are: 2.5kW – 4.0kW – 6.0kW – 7.4kW.
Press to conrm.
The selected power will remain in the memory, even in the case of a
power outage.
To vary power levels, disconnect the appliance from the mains power
for at least 60seconds, then reconnect it and repeat the steps above.
In case of error during the setting sequence, the display will show the
symbol and an acoustic signal will be sounded. In this case, you will
need to repeat the operation.
If the error persists, contact the assistance service.
ACOUSTIC SIGNAL ON / OFF
To switch the acoustic signal on/o:
Switch on the cook top.
Hold down the
P
control on the rst slider to the left, for 3seconds.
Any alarms set will remain active.
3”
OFF
P
Max
18
MinMed
OFF
P
Max
18
MinMed
OFF
P
Max
18
MinMed
OFF
P
Max
18
MinMed
SWITCHING THE HOB ON/OFF
To turn the hob on, press the power button for around 1 second, until
the cooking zone display lights up.
To turn the hob o, press the same button again, and all cooking zones
will be deactivated.
If no function is selected, the hob will automatically switch o after 10 seconds.
If the hob is being used, switching it o will switch o all cooking zones,
and the residual heat indicator, “H”, will remain lit until all of the cooking
zones have cooled.
POSITIONING
1. Locate the desired cooking zone, by referring to the position
symbols at the bottom of each slide touchscreen.
2. Place the pan in the chosen area, making sure that it covers one or
more of the reference marks on the surface of the hob.
3. Do not cover the control panel symbols with the cooking pot.
ACTIVATING/DEACTIVATING COOKING ZONES AND ADJUSTING
POWER LEVELS
To switch on a cooking zone:
1. Switch on the hob.
2. Set the required power level by sliding your nger across the slider
control (SLIDER) for the cooking zone of choice.
The power level will appear above the slider. Each cooking zone has
dierent power levels, ranging from “1” (minimum) to “18” (maximum).
Using the slider controls it is also possible to select the quick heat
P
function, which is marked “P” on the display.
To switch o the cooking zones:
Use the “OFF” control at the start of the slider control. If the cooking
zone is still hot, the residual heat indicator “H” will appear on the display.
Vue de la page 5
1 2 3 4 5 6 7 8 9 10 11 12 13 14

Commentaires sur ces manuels

Pas de commentaire