Hotpoint KIA 320 XS C Mode d'emploi télécharger pdf (Page 9)

EN8

Timer

The timer can be used to set the cooking time for a maximum of 99 minutes (1 hour and 39 minutes) for all the cooking zones.

Select the cooking zone to be used with the timer, press the timer and a beep signals the function (see figure). The display shows “00” and the LED indication

comes on. The Timer value can be decreased and increased by keeping the slider function “+” and “-” buttons pressed. When the set time has elapsed, an acoustic

signal sounds and the cooking zone switches off automatically. To deactivate the timer, keep the Timer button pressed for at least 3 seconds.

To set the timer for another zone, repeat the above steps. The timer display always shows the timer for the selected zone or the shortest timer.

To modify or deactivate the timer, press the cooking zone selection button for the timer in question.

Residual heat indicator.

The hob is fitted with a residual heat indicator for each cooking zone. These indicators alert the user when cooking zones are still hot.

If the display shows , the cooking zone is still hot. If the residual heat indicator of a given cooking zone is lit, that zone can be used, for example, to keep a

dish warm or to melt butter.

When the cooking zone cools down, the display goes off.

Incorrect or missing pot indicator.

If you are using a pot that is not suitable, not correctly positioned or not of the correct dimensions for your induction hob, the message “no pot” will

appear in the display (see figure at side). If no pot is detected within 60 seconds, the hob switches off.

Fast boil function (Booster)

This function, only present on some cooking zones, makes it possible to exploit the hob’s maximum power (for example to bring water to the boil very quickly). To

activate the function, press the “+” button until “P” appears on the display. After 10 minutes’ use of the booster function, the appliance automatically sets the zone to

level 9.

IMPORTANT: Do not use abrasive sponges or scouring pads. Their use could eventually ruin the glass.

• After each use, clean the hob (when it is cool) to remove any deposits and stains due to food residuals.

• Sugar or foods with a high sugar content damage the hob and must be immediately removed.

• Salt, sugar and sand could scratch the glass surface.

• Use a soft cloth, absorbent kitchen paper or a specific hob cleaner (follow the Manufacturer’s instructions).

• Liquid splillages on the cooking zones may make pan vibrate or move

• Dry the hob thoroughly after cleaning it.

•

• Read and follow the instructions given in the section “Instructions for use”.

• Check that the electricity supply has not been shut off.

• Dry the hob thoroughly after cleaning it.

• If, when the hob is switched on, alphanumeric codes appear on the display, consult the following table for instructions.

• If the hob cannot be switched off after using it, disconnect it from the power supply.

CLEANING

WARNING

- Do not use steam cleaners.

- Before cleaning, make sure the cooking zones are switched off and that the residual heat indicator (“H”)

is not displayed.

TROUBLESHOOTING GUIDE

ERROR CODE DESCRIPTION POSSIBLE CAUSES ERROR ELIMINATION

C81, C82

The control panel switches off

because of excessively high

temperatures

The internal temperature of electronic

parts is too high

Wait for the hob to cool down

before using it again.

F42 or F43 The connection voltage is wrong

The sensor detects a discrepancy

between the appliance voltage and

that of the mains supply

Disconnect the hob from the

mains and check the electrical

connection

F12, F21, F25, F36, F37, F40, F47, F56, F58,

F60

Call the After-Sales Service and specify the error code

1 2 3 4 5 6 7 8 9 10 11

Commentaires sur ces manuels

Pas de commentaire

Hotpoint KIA 320 XS C Mode d'emploi Page 9

Commentaires sur ces manuels

Produits connexes et manuels pour Plaques chauffantes Hotpoint KIA 320 XS C