Hotpoint SX1046S L P 0 X Mode d'emploi télécharger pdf (Page 5)

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Installation

! Please keep this instruction booklet in a safe place for future reference. If

the appliance is sold, given away or moved, please make sure the booklet is

alsopassedontothenewownerssothattheymaybenetfromtheadvice

contained within it.

! Please read this instruction manual carefully: it contains important information

concerning the safe operation, installation and maintenance of the appliance.

Positioning

!Donotletchildrenplaywiththepackagingmaterial;itshouldbedisposed

of in accordance with local separated waste collection standards (see

Precautions and tips).

!Theappliancemustbeinstalledbyaqualiedprofessionalinaccordance

with the instructions provided. Incorrect installation may damage property or

cause harm to people or animals.

Built-in appliances

Use an appropriate cabinet to ensure that the appliance operates properly:

• thepanelsadjacenttotheovenmustbemadeofheat-resistantmaterial.

• cabinetswithaveneerexteriormustbeassembledwithglueswhichcan

withstand temperatures of up to 100°C.

• toinstalltheovenunder the counter (see diagram) or in a kitchen unit,

the cabinet must have the following dimensions:

590 mm.

595 mm.

22,5 mm.*

20,5 mm.

550 mm.

570 mm.

20 mm.

575-585 mm.

45 mm.

560 mm.

550 mm.

min.

! The appliance must not come into contact with electrical parts once it has

been installed.

The indications for consumption given on the data plate have been calculated

for this type of installation.

Ventilation

To ensure adequate ventilation, the back panel of the cabinet must be

removed. It is advisable to install the oven so that it rests on two strips of

wood,oronacompletelyatsurfacewithanopeningofatleast45x560

mm (see diagrams).

560 mm.

45 mm.

Centring and xing

Secure the appliance to the cabinet:

• opentheovendoor.

• slideoutthesidegasketsatthetopuntilthe2xingholesareexposed;

• xtheoventothecabinetusingthe2woodscrews.

• repositionthe2gaskets.

! All parts which ensure the safe operation of the appliance must not be

removable without the aid of a tool.

Electrical Connection

The electrical connection to the mains must be made on the appliance. The

power voltage and frequency are as indicated on the rating plate.

! THIS APPLIANCE MUST BE EARTHED.

Fitting the power supply cable

1. Open the terminal board by inserting a

screwdriver into the side tabs of the cover.

Use the screwdriver as a lever by pushing

it down to open the cover (see diagram).

2. Install the power supply cable by

loosening the cable clamp screw

and the three wire contact screws

L-N- .

Connect the wires to the corresponding

terminals: the Blue wire to the terminal

marked (N), the Brown wire to the terminal

marked (L) and the Yellow/Green wire to

the terminal marked

(see diagram).

3. Secure the cable by fastening the

clamp screw.

4. Close the cover of the terminal board.

Electrical Connection:

Voltage Frequency: see data plate

FuseSection:16A

Supply cable: 3x1.5mm

You can connect your oven to the system means of a terminal board. Refer

to above information for the minimal cable sections and the calibration of the

protective elements according to the connection.

If the appliance is installed with a junction box, an omnipolar circuit breaker

- with a minimum contact opening of 3mm - should be installed between the

appliance and the mains.

1 2 3 4 5 6 7 8 9 10 ... 19 20

Commentaires sur ces manuels

Pas de commentaire

Hotpoint SX1046S L P 0 X Mode d'emploi Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Non Hotpoint SX1046S L P 0 X